Accessories - Makita DA392D Betriebsanleitung

CAUTION:
• Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool perfor-
mance and shorten the service life of the tool.
• There is a tremendous twisting force exerted on the
tool/bit at the time of hole breakthrough. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece. Use both hands to help control
the tool.
• A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
However, the tool may back out abruptly if you do not
hold it firmly.
• Always secure small workpieces in a vise or similar
hold-down device.
Screwdriving operation (Fig. 6)
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the trigger just as
the screw bottoms out. If the trigger is not released, the
screw may strip out the hole or the screw and/or bit may
be damaged.
NOTE:
• Make sure that the driver bit is inserted straight in the
screw head, or the screw and/or bit may be damaged.
• When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.
• If the tool is operated continuously until the battery car-
tridge has discharged, allow the tool to rest for 15 min-
utes before proceeding with a fresh battery.
Nominal diameter of
wood screw (mm)
3.1
3.5
3.8
4.5
Installing set plate (Optional accessory) (Fig. 7)
Always install the set plate when using battery cartridges
9100, 9102, 9102A for Model DA392D and 1200, 1202,
1200A, 1202A for Model DA312D. Install the set plate on
the tool with the screw provided.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work on
the tool.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
Recommended size of
pilot hole (mm)
2.0 – 2.2
2.2 – 2.5
2.5 – 2.8
2.9 – 3.2

ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Screw bits
• Rubber pad assembly
• Foam polishing pad 125
• Wool bonnet 100
• Various type of Makita genuine batteries and chargers
• Plastic carrying case
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-1:
Sound pressure level (L
The noise level under working may exceed 85 dB (A).
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745-2-1:
Work mode: Drilling into metal
Vibration emission ( a
EC-DECLARATION OF CONFORMITY
Model; DA302D, DA392D, DA312D
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents,
EN60745, EN55014
in accordance with Council Directives, 2004/108/EC and
98/37/EC.
Tomoyasu Kato
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
): 70 dB (A) or less
pA
2
): 2.5 m/s or less
h,D
CE 2007
Director
ENH102-7
7