Ec Declaration Of Conformity; Technical Data; General Safety Instructions - DeWalt DW739 Originalanweisungen

BANDSAW
DW738, DW739
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
E
product development and innovation make D
reliable partners for professional power tool users.

Technical Data

Voltage V
UK & Ireland only V
Type
Power input W
Cutting speed m/min
Motor speed min
Max. cutting height mm
Max. cutting width mm
Table size mm
Table inclination
Overall height mm
Overall width mm
Overall depth mm
Weight kg
L (sound pressure) dB(A)
PA
K (sound pressure
PA
uncertainty) dB(A)
L (sound power) dB(A)
WA
K (sound power
WA
uncertainty) dB(A)
NOTE: This device is intended for the connection to a power supply
system with maximum permissible system impedance Zmax of 0.25
OHM at the interface point (power service box) of user's supply.
The user has to ensure that this device is connected only to a power
system which fulfils the requirement above. If necessary, the user can
ask the public power supply company for the system impedance at the
interface point.
Fuses:
Europe 230 V tools
U.K. & Ireland 230 V tools
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
WARNING: indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
NOTICE: Indicates a practice not related to personal
injury which, if not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
Denotes sharp edges.
WALT one of the most
E
DW738 DW739
230
230/115 230/115
3
750
330/800 330-800
1 2830
155
310
380 x 380 380 x 380
0–45° 0–45°
970
510
660
23
92.0
3.3
105.0 105.0
4.0
10 Amperes, mains
13 Amperes, in plugs
EC-Declaration of Conformity
MACHINERY DIRECTIVE
DW738, DW739
D WALT declares that these products described under Technical Data
E
are in compliance with: 2006/42/EC, EN 61029-1, EN 61029-2-5.
230
These products also comply with Directive 2004/108/EC and
2011/65 EU. For more information, please contact D
3
following address or refer to the back of the manual.
750
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of D
2830
155
310
Horst Grossmann
970
Vice President Engineering and Product Development
510
D WALT, Richard-Klinger-Straße 11,
E
660
D-65510, Idstein, Germany
23
01.01.2010
92.0
WARNING: to reduce the risk of injury, read the instruction
manual.
3.3

General Safety Instructions

WARNING! When using electric tools basic safety
4.0
precautions should always be followed to reduce the risk
of fire, electric shock and personal injury including the
following.
Read all of these instructions before attempting to operate this product
and save these instructions.
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3. Guard against electric shock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g., high humidity, when metal swarf is being
produced, etc.), electric safety can be improved by inserting an
isolating transformer or a (FI) earth-leakage circuit-breaker.
4. Keep other persons away.
Do not let persons, especially children, not involved with the work,
touch the tool or the extension cord and keep them away from the
work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was
intended.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do
not use tools for purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
WALT.
E
SAVE THIS MANUAL FOR FUTURE REFERENCE
E NG L I S H
WALT at the
E
19