EINHELL GE-CM 36/43 Li M Originalbetriebsanleitung Seite 23

The cutting height is adjusted as follows
(see Fig. 10):
1. Push the lever (A) outwards.
2. Set the lever (B) to the desired cutting height.
3. Release the lever (A) and check that it is se-
curely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-75 mm
in 6 intervals, and can be read off on the scale
(Fig. 12/D).
Using the mulching adapter (Fig. 11)
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Notice! Mulching is only possible if the lawn is
relatively short.
Warning!
Insert the mulching adapter only when the engi-
ne is switched off and the safety plug has been
pulled out.
To use the mulching function, disconnect the
debris bag, slide the mulching adaptor (Fig. 11/
Item 23) into the ejector opening and close the
ejector fl ap.
Installing the battery (Fig. 12)
Open the battery cover. Then insert the batteries
in the mounts as shown in Fig. 12.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Charging the battery (Fig. 13)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons
(Fig. 12/Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
Anl_GE_CM_36_43_Li_M_2x4Ah_SPK13.indb 23 Anl_GE_CM_36_43_Li_M_2x4Ah_SPK13.indb 23
GB
3. Insert the battery pack into the battery char-
ger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 14)
Press the button for the battery capacity indicator
(A). The battery capacity indicator (B) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
- 23 -
15.07.2021 10:10:51 15.07.2021 10:10:51