Elektro-Automatik PS 9000 1U Betriebsanleitung Seite 59

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Explanation of symbols ..................................5
1.2 Warranty .........................................................5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical data ................................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ...................................9
1.8.3 Specific technical data .................................10
1.8.4 Views ............................................................14
1.9 Construction and function ............................18
1.9.1 General description ......................................18
1.9.2 Block diagram ..............................................18
1.9.3 Scope of delivery .........................................18
1.9.4 The control panel (HMI) ...............................19
1.9.5 Share Bus-Connection ................................20
1.9.6 USB port .......................................................21
1.9.7 Ethernet port ................................................21
1.9.8 Analog interface ...........................................21
1.9.9 Sense connector (remote sensing) .............21
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................22
2.1.1 Transport ......................................................22
2.1.2 Packaging ....................................................22
2.1.3 Storage .........................................................22
2.2 Unpacking and visual check ........................22
2.3 Installation ....................................................22
2.3.1 Safety procedures before installation and
use ................................................................22
2.3.2 Preparation ...................................................22
2.3.3 Installing the device .....................................23
2.3.4 Connection to AC supply .............................23
2.3.5 Connection to DC loads ...............................24
2.3.6 Grounding of the DC output ........................25
2.3.7 Connection of remote sensing ....................25
2.3.8 Connecting the "Share" bus ........................25
2.3.9 Connecting the analog interface .................26
2.3.10 Connecting the USB port .............................26
2.3.11 Initial commission .........................................26
2.3.12 Initial network setup .....................................27
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
2.3.13 Commission after a firmware update or a
3
OPERATION AND APPLICATION
3.1
3.1.1
3.1.2
3.2
3.2.1
3.2.2
3.2.3
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.9.1
3.9.2
3.9.3
3.9.4
4
SERVICE AND MAINTENANCE
4.1
4.2
4.2.1
4.2.2
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
PS 9000 1U Series
long period of non-use .................................27
Important notes ............................................28
Personal safety ............................................28
General .........................................................28
Operating modes .........................................28
Voltage regulation / Constant voltage .........28
Current regulation / constant current / current
limiting ..........................................................28
Power regulation / constant power / power
limiting ..........................................................29
Alarm conditions ..........................................30
Power Fail ...................................................30
Overtemperature ..........................................30
Overvoltage ..................................................30
Overcurrent ..................................................30
Overpower ....................................................30
Manual operation .........................................31
Switching on the device ...............................31
Switching off the device ...............................31
Configuration in the setup menu .................31
Adjustment limits ..........................................35
Display modes for actual and set values ....36
Manual adjustment of set values .................36
The quick menu ...........................................37
Switching the DC output on or off ................37
Remote control .............................................38
General .........................................................38
Control locations ..........................................38
Remote control via a digital interface ..........38
Remote control via the analog interface
(AI) ................................................................39
Alarms and monitoring .................................43
Definition of terms ........................................43
Device alarm handling .................................43
Control panel (HMI) lock ..............................44
Loading and saving a user profile ...............45
Other applications ........................................46
Parallel operation in Share Bus mode ........46
Series connection ........................................47
Operation as battery charger .......................47
Two quadrants operation (2QO) ..................48
Maintenance / cleaning ................................50
Fault finding / diagnosis / repair...................50
Replacing a defect mains fuse ....................50
Firmware update ..........................................50
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3