Technical Data; Before Starting The Equipment; Attachment And Operation; Mains Connection - Scheppach HC20Si Twin Original Bedienungsanleitung

Residual risks
Comply with the stipulated maintenance and safety
instructions in the operating instructions.
Remain attentive at all times when working, and keep
third parties at a safe distance from your work area.
Even when the device is being used properly, there
will always be certain residual hazards that cannot be
completely ruled out. The following potential hazards
can arise due to the type and design of the device:
• Unintentional starting up of the product.
• Damage to hearing if the stipulated hearing
protection is not worn.
• Dirt particles, dust etc. can get irritate the eyes or
face despite wearing safety goggles.
• Inhaling swirled up particles.

6. Technical data

Mains connection

Motor rating
Operating mode
Compressor speed
Pressure vessel capacity
Operating pressure
Theoretical intake capacity
Effective delivery quantity at
1 bar
Protection type
Weight of the unit
Max. altitude
(above mean sea level)
Protection class
The noise emission values were measured in accord-
ance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
m Warning: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
Sound power level L
wA
Sound pressure level L
pA
Uncertainty K
wA/pA

7. Before starting the equipment

• Open the packaging and carefully remove the de-
vice.
230 V~ 50 Hz
750 W
S1
1400 min
-1
20 l
approx. 10 bar
approx. 200 l/min
approx. 89 l/min
IP20
approx. 30 kg
1000 m
I
80 dB(A)
54 dB(A)
3 dB(A)
www.scheppach.com
• Remove the packaging material, packaging and
transport safety devices (if applicable).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the end of the
warranty period.
DANGER
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.

8. Attachment and operation

m Important!
You must fully assemble the appliance before using it
for the first time!
8.1 Fitting the compressed air hose (fig. 2)
• Connect the plug nipple of the compressed air hose
(not included in the scope of delivery) to one of the
quick couplings (13). Then attach the compressed
air tool to the quick coupling of the compressed air
hose.
8.2 Mains connection
• The compressor is equipped with a mains cable
with shock-proof plug. This can be connected to
any 230 - 240 V~ 50 Hz shock-proof socket.
GB | 47