Adjustment - DeWalt DW716 Bersetzt Von Den Originalanweisungen

Continue to hold the lock button in to keep the spindle from turning
(fig. D2).
• Remove the blade locking screw (33) and the outside arbor collar (34).
• Install the saw blade (35) onto the blade adaptor (36) seated directly
against the inside arbor collar (37), making sure that the teeth at the
bottom edge of the blade are pointing toward the back of the saw
(away from the operator).
• Replace the outer arbor collar (34).
• Tighten the blade locking screw (33) carefully by turning counter-
clockwise while holding the spindle lock engaged with your other hand.
WARNING! Be aware the saw blade shall be replaced in the
described way only. Only use saw blades as specified under
Technical Data; Cat.no.: DT4330 is suggested.

ADJUSTMENT

WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Your mitre saw was accurately adjusted at the factory. If readjustment due
to shipping and handling or any other reason is required, follow the steps
below to adjust your saw. Once made, these adjustments should remain
accurate.
Checking and Adjusting the Blade to the Fence (fig. E1–E4)
• Release the mitre lever (4) and squeeze the mitre latch (5) upwards to
release the mitre arm (38).
• Swing the mitre arm until the latch locates it at the 0° mitre position.
Do not tighten the lever.
• Pull down the head until the blade just enters the saw kerf (39).
• Place a square (40) against the left side of the fence (3) and blade (35)
(fig. E3).
WARNING: Do not touch the tips of the blade teeth with the
square.
• If adjustment is required, proceed as follows:
• Loosen the screws (41) and move the scale/mitre arm assembly left or
right until the blade is at 90° to the fence as measured with the square.
• Retighten the screws (41). Pay no attention to the reading of the mitre
pointer at this point.
Adjusting the Mitre Pointer (fig. E1, E2, F)
• Release the mitre lever (4) and squeeze the mitre latch (5) upwards to
release the mitre arm (38).
• Move the mitre arm to set the mitre pointer (42) to the zero position, as
shown in fig. F.
• With the mitre lever loose, allow the mitre latch to snap into place as
you rotate the mitre arm past zero.
• Observe the pointer (42) and mitre scale (6) through the viewing opening
(43). If the pointer does not indicate exactly zero, loosen the screw (45),
move the plastic moulding (44) to read 0° and tighten the screw.
Mitre lock/Detent Rod Adjustment (fig. G)
If the base of the saw can be moved while the mitre lever (4) is locked, the
mitre lock/detent rod (47) must be adjusted.
• Unlock the mitre lever (4).
• Loosen the locking screw (46) using an hex key.
• Fully tighten the mitre lock/detent rod (47) using a screwdriver. Then
loosen the rod a quarter of a turn.
• Check that the table does not move when the lever (4) is locked at a
random (not preset) angle.
• Tighten the locking screw (46).
All manuals and user guides at all-guides.com
Checking and Adjusting the Blade to the Table (fig. H1–H4)
• Loosen the bevel clamp handle (14).
• Press the saw head to the right to ensure it is fully vertical and tighten
• Pull down the head until the blade just enters the saw kerf (39).
• Place a set square (40) on the table and up against the blade (35)
• If adjustment is required, proceed as follows:
• Loosen the bevel clamp handle (14) and turn the vertical position
• If the bevel pointer (48) does not indicate zero on the bevel scale (15),
Adjusting the Fence (fig. I1, I2)
The upper part of the fence can be adjusted to provide clearance, allowing
the saw to bevel to a full 50° both left and right.
To Adjust the Left Fence (3)
• Loosen the plastic knob (50) and slide the fence to the left.
• Make a dry run with the saw switched off and check for clearance.
• Tighten the knob securely.
To Adjust the Right Fence (7)
• Loosen the plastic knob (51) and slide the fence to the right.
• Proceed as for adjusting the left fence.
Overriding the Right Bevel Lock (fig. H1)
The right bevel is locked to facilitate the setting of the saw blade in the
vertical position.
• To override the right bevel lock, pull out the override pin (20) and turn it
• To discontinue the override, turn the pin half a turn back in its original
Checking and Adjusting the Bevel Angle (fig. I1, I2, J1–J3)
Left Bevel Angle
• Loosen the left side fence clamping knob (50) and slide the upper part
• Loosen the bevel clamp handle (14) and with the intermediate bevel
• If adjustment is required, proceed as follows:
• Turn the bevel position adjustment stop screw in or out as necessary
• To achieve a 50° bevel, loosen the screw on the angle position stop
Right Bevel Angle
• Loosen the right side fence clamping knob (51) and slide the upper part
the bevel clamp handle.
(fig. H2).
WARNING: Do not touch the tips of the blade teeth with the
square.
adjustment stop screw (19) in or out until the blade is at 90° to the table
as measured with the square.
loosen the screw (49) that secures the pointer and move the pointer as
necessary.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and down
movement of the arm.
WARNING: The guide grooves (52) can become clogged with
sawdust. Use a stick or some low pressure air to clear the guide
grooves.
half a turn to keep it in this position.
position. The lock re-engages as soon as the saw blade reaches vertical
position.
of the left side fence to the left as far as it will go.
position stop (53) turned aside move the saw arm to the left until the
angle position stop (54) rests against the bevel position adjustment stop
(55). This is the 45° bevel position.
until the pointer (48) indicates 45° with the angle position stop resting
against the bevel position adjustment stop.
and slide the stop out of the way to allow the saw arm to move as
necessary.
of the right side fence to the right as far as it will go.
E N G L I S H
31