Optional Accessories - Makita LS1040 Bedienungsanleitung

Bevel angle
0° bevel angle
► Fig.38: 1. Turn base 2. Lever 3. 0° adjusting bolt
Lower the handle fully and lock it in the lowered position by push-
ing in the stopper pin. Loosen the lever at the rear of the tool.
Turn the 0° bevel angle adjusting bolt on the right side
of the turn base two or three revolutions clockwise to tilt
the blade to the right.
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the 0° bevel angle adjusting bolt
counterclockwise. Then tighten the lever securely.
► Fig.39: 1. Triangular rule 2. Saw blade 3. Top sur-
face of turn base
Make sure that the pointer on the turn base point to 0°
on the bevel scale on the arm. If it does not point to 0°,
loosen the screw which secures the pointer and adjust
the pointer so that it will point to 0°.
► Fig.40: 1. Arm 2. Bevel scale 3. Pointer 4. Turn base
45° bevel angle
► Fig.41: 1. Lever 2. Arm 3. Pointer 4. 45° bevel angle
adjusting bolt
Adjust the 45° bevel angle only after performing 0° bevel angle
adjustment. To adjust left 45° bevel angle, loosen the lever and
tilt the blade to the left fully. Make sure that the pointer on the
arm points to 45° on the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the 45° bevel angle adjusting
bolt on the left side of the arm until the pointer points to 45°.
Replacing fluorescent tube
Only for model LS1040F / LS1040FS
► Fig.42: 1. Pull out 2. Push 3. Lamp box 4. Screws
5. Fluorescent tube
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent tube.
• Do not apply force, impact or scratch to a fluorescent
tube, which can cause a glass of the fluorescent tube to
be broken resulting in a injury to you or your bystanders.
• Leave the florescent tube for a while immedi-
ately after a use of it and then replace it. If not.
You may burn yourself.
Remove screws, which secure Lamp Box for the light.
Pull out the Lamp Box keeping pushing lightly the upper
position of it as illustrated on the left.
Pull out the fluorescent tube and then replace it with
Makita original new one.
Replacing carbon brushes
► Fig.43: 1. Limit mark
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
► Fig.44: 1. Screwdriver 2. Brush holder cap
After use
• After use, wipe off chips and dust adhering to the
tool with a cloth or the like. Keep the blade guard
clean according to the directions in the previously
covered section titled "Blade guard". Lubricate the
sliding portions with machine oil to prevent rust.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
WARNING:
attachments are recommended for use with your
Makita tool specified in this manual. The use of
any other accessories or attachments may result in
serious personal injury.
WARNING:
or attachment for its stated purpose. Misuse of
an accessory or attachment may result in serious
personal injury.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Steel & Carbide-tipped saw blade
(Refer to our website or contact your local Makita
dealer for the correct saw blades to be used for
the material to be cut.)
• Auxiliary plate
• Vise assembly (Horizontal vise)
• Vertical vise
• Socket wrench
• Holder set
• Holder assembly
• Holder rod assembly
• Set plate
• Dust bag
• Triangular rule
• Fluorescent tube
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
16 ENGLISH
These Makita accessories or
Only use the Makita accessory