Optional Accessories - Makita LXT DLS110 Betriebsanleitung

45° bevel angle
NOTICE:
Before adjusting the 45° bevel angle,
¿QLVK ƒ EHYHO DQJOH DGMXVWPHQW
Loosen the knob and fully tilt the carriage to the side
that you want to check. Check if the pointer indicates
the 45° position in the bevel angle scale.
Fig.74
If the pointer does not indicate the 45° position, align
LW ZLWK ƒ SRVLWLRQ E\ WXUQLQJ WKH DGMXVWLQJ EROW RQ WKH
opposite side of the bevel angle scale.
Fig.75: 1. /HIW ƒ DGMXVWLQJ EROW 2. 5LJKW ƒ DGMXVW-
ing bolt
Adjusting the laser line position
For DLS111, DLS112 only
WARNING:
The batteries must be installed
while adjusting the laser line. Take extra care not
to switch on the tool during adjustment. $FFLGHQWDO
VWDUW XS RI WKH WRRO PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
CAUTION:
Never look directly into the laser
beam. Direct eye exposure to the beam could cause
serious damage to your eyes.
NOTICE:
Check the position of laser line regu-
larly for accuracy.
NOTICE:
Beware that impacts to the tool. It may
cause the laser line to be misaligned or may cause
damage to the laser, shortening its life.
NOTICE:
Have the tool repaired by a Makita
authorized service center for any failure on the
laser unit.
7KH PRYDEOH UDQJH RI ODVHU OLQH LV GHFLGHG E\ WKH UDQJH
DGMXVWPHQW VFUHZV RQ ERWK VLGHV 3HUIRUP IROORZLQJ
procedures to alter the laser line position.
1. Remove the batteries.
2. Draw a cutting line on the workpiece and place it
RQ WKH WXUQ EDVH $W WKLV WLPH GR QRW VHFXUH WKH ZRUN-
piece with a vise or similar securing device.
3. Lower the handle and align the cutting line with
the saw blade.
4. Return the handle to the original position and secure
the workpiece with the vertical vise so that the workpiece
does not move from the position you have determined.
5. Install the batteries and turn on the laser switch.
6. /RRVHQ WKH DGMXVWLQJ VFUHZ 7R PRYH WKH ODVHU OLQH
DZD\ IURP WKH EODGH WXUQ WKH UDQJH DGMXVWPHQW VFUHZV
FRXQWHUFORFNZLVH 7R PRYH WKH ODVHU OLQH FORVH WR WKH
EODGH WXUQ WKH UDQJH DGMXVWPHQW VFUHZ FORFNZLVH
Adjusting the laser line on the left side of the blade
Fig.76: 1. $GMXVWLQJ VFUHZ 2. 5DQJH DGMXVWPHQW VFUHZ
3. Hex wrench 4. Laser line 5. Saw blade
Adjusting the laser line on the right side of the blade
Fig.77: 1. $GMXVWLQJ VFUHZ 2. 5DQJH DGMXVWPHQW VFUHZ
3. Hex wrench 4. Laser line 5. Saw blade
7. 6OLGH WKH DGMXVWLQJ VFUHZ WR WKH SRVLWLRQ WKDW WKH
laser line comes onto the cutting line and then tighten.
NOTE: 7KH PRYDEOH UDQJH RI ODVHU OLQH LV IDFWRU\ DGMXVWHG
ZLWKLQ  PP  IURP WKH VLGH VXUIDFH RI EODGH
Cleaning the laser light lens
For DLS111, DLS112 only
7KH ODVHU OLJKW EHFRPHV KDUG WR VHH DV WKH OHQV IRU WKH ODVHU
light gets dirty. Clean the lens for laser light periodically.
Fig.78: 1. Screw 2. Lens
Remove the batteries. Loosen the screw and pull out
the lens. Clean the lens gently with a damp soft cloth.
NOTICE:
Do not remove the screw which
secures the lens. If the lens does not come out,
loosen the screw further.
NOTICE:
Do not use solvents or any petro-
leum-based cleaners on the lens.
After use
$IWHU XVH ZLSH RII FKLSV DQG GXVW DGKHULQJ WR WKH WRRO
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
VHFWLRQ WLWOHG %ODGH JXDUG  /XEULFDWH WKH VOLGLQJ SRU-
tions with machine oil to prevent rust.
7R PDLQWDLQ SURGXFW 6$)(7< DQG 5(/,$%,/,7<
UHSDLUV DQ\ RWKHU PDLQWHQDQFH RU DGMXVWPHQW VKRXOG
EH SHUIRUPHG E\ 0DNLWD $XWKRUL]HG RU )DFWRU\ 6HUYLFH
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
WARNING:
attachments are recommended for use with your
0DNLWD WRRO VSHFL¿HG LQ WKLV PDQXDO 7KH XVH RI
any other accessories or attachments may result in
VHULRXV SHUVRQDO LQMXU\
WARNING:
or attachment for its stated purpose. Misuse of
an accessory or attachment may result in serious
SHUVRQDO LQMXU\
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
‡ 6WHHO &DUELGHWLSSHG VDZ EODGHV
‡ 9HUWLFDO YLVH
‡ +RUL]RQWDO YLVH
‡ &URZQ PROGLQJ VWRSSHU VHW
‡ 'XVW EDJ
‡ 7ULDQJXODU UXOH
‡ +H[ ZUHQFK
‡ +H[ ZUHQFK IRU ODVHU DGMXVWPHQW
‡ :LUHOHVV XQLW IRU '/6
‡ 0DNLWD JHQXLQH EDWWHU\ DQG FKDUJHU
NOTE: Some items in the list may be included in the
WRRO SDFNDJH DV VWDQGDUG DFFHVVRULHV 7KH\ PD\
differ from country to country.
35 ENGLISH
These Makita accessories or
Only use the Makita accessory