Replacing Carbon Brushes; After Use; Optional Accessories - Makita LS0815F Bedienungsanleitung

scale. Then turn the turn base slightly clockwise and
counterclockwise to seat the turn base in the 0° miter
notch. (Leave as it is if the pointer does not point to
0°.) Loosen the hex sockets bolts securing the guide
fence using the socket wrench.
Fig.41
Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin. Square the
side of the blade with the face of the guide fence
using a triangular rule, try-square, etc. Then
securely tighten the hex socket bolts on the guide
fence in order starting from the right side.
Fig.42
Make sure that the pointer points to 0° on the miter
scale. If the pointer does not point to 0°, loosen
the screw which secures the pointer and adjust the
pointer so that it will point to 0°.
2. Bevel angle
(1) 0° bevel angle
Fig.43
Push the carriage toward the guide fence and
tighten the locking screw to secure the carriage.
Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin. Loosen
the lever at the rear of the tool.
Fig.44
Turn the hex bolt on the right side of the arm
two or three revolutions counterclockwise to
tilt the blade to the right.
Fig.45
Carefully square the side of the blade with
the top surface of the turn base using the
triangular rule, try-square, etc. by turning the
hex bolt on the right side of the arm
clockwise. Then tighten the lever securely.
Fig.46
Make sure that the pointer on the arm point to 0°
on the bevel scale on the arm holder. If they do
not point to 0°, loosen the screw which secure
the pointer and adjust it so that it will point to 0°.
(2) 45° bevel angle
Fig.47
Adjust the 45° bevel angle only after
performing 0° bevel angle adjustment. To
adjust left 45° bevel angle, loosen the lever
and tilt the blade to the left fully. Make sure
that the pointer on the arm points to 45° on
the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the 45°
bevel angle adjusting bolt on the right side of
the arm holder until the pointer points to 45°.
To adjust the right 5° bevel angle, perform
the same procedure as that described above.
All manuals and user guides at all-guides.com

Replacing carbon brushes

Fig.48
Remove and check the carbon brushes regularly.
Replace when they wear down to 3 mm in length. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Fig.49
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.

After use

To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.

OPTIONAL ACCESSORIES

If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
006526
NOTE:
19
After use, wipe off chips and dust adhering to the
•
tool with a cloth or the like. Keep the blade guard
clean according to the directions in the previously
covered section titled "Blade guard". Lubricate the
sliding portions with machine oil to prevent rust.
When storing the tool, pull the carriage toward you fully.
•
WARNING:
These Makita accessories or attachments are
•
recommended for use with your Makita tool specified
in this manual. The use of any other accessories or
attachments may result in serious personal injury.
Only use the Makita accessory or attachment
•
for its stated purpose. Misuse of an accessory or
attachment may result in serious personal injury.
Steel & Carbide-tipped saw blades
•
Miter saw blades For smooth and precise cutting in various materials.
General purpose blade for fast and smooth rip,
Combination
crosscuts and miters.
For smoother cross grain cuts. Slices cleanly
Crosscutting
against the grain.
Fine cross cuts For sand-free cuts cleanly against the grain.
Non-ferrous metals For miters in aluminum, copper, brass, tubing,
miter saw blades and other non-ferrous metals.
Vertical vise
•
Socket wrench with hex wrench on its other end
•
Holder
•
Dust bag
•
Triangular rule
•
Some items in the list may be included in the tool
•
package as standard accessories. They may differ
from country to country.