Cleaning; Storage; Maintenance; Disposal And Recycling - Scheppach CID27-12Li Original Bedienungsanleitung

Take the rotating drill bit out of the hole frequently so
that swarf or drill dust can be re-moved and the hole
and tool is ventilated.
Drilling in metal:
Use a metal drill bit (HSS). For the best results, you
should cool the bit with oil.
Metal drill bits can also be used to drill into plastic.
Drilling in stone:
Use a circular shafted masonry drill bit with a hard-
ened metal tip.
Drilling in wood:
Normally you should use a wood drill with a cen-
tring point. For deep holes, use an auger type bit.
For large diameter holes, use a forstner bit. You can
screw small screws into soft wood without the need
for pre-drilling.

12. Cleaning

Danger!
Always pull out the battery pack before starting any
cleaning work.
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.

13. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

14. Maintenance

There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consumables.
Wear parts*: carbon brushes
* Not necessarily included in the scope of delivery!

15. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU) pertain-
ing to waste electrical and electronic equipment
(WEEE). This product must be disposed of at a des-
ignated collection point. This can occur, for example,
by handing it in at an authorised collecting point for
the recycling of waste electrical and electronic equip-
ment. Improper handling of waste equipment may
have negative consequences for the environment
and human health due to potentially hazardous sub-
stances that are often contained in electrical and
electronic equipment. By properly disposing of this
product, you are also contributing to the effective use
of natural resources. You can obtain information on
collection points for waste equipment from your mu-
nicipal administration, public waste disposal authori-
ty, an authorised body for the disposal of waste elec-
trical and electronic equipment or your waste disposal
company.
Batteries and rechargeable batteries do not be-
long in the household waste!
As the consumer you are required by law to
bring all batteries and rechargeable batteries,
regardless whether they contain harmful sub-
stances* or not, to a collection point run by the local
authority or to a retailer, so that they can be disposed
of in an environmentally friendly manner.
*labelled with: Cd = cadmium, Hg = mercury, Pb =
lead