Before Starting The Machine - EINHELL TKS 1700 Bedienungsanleitung

Anleitung_TKS_1700_4340668:_
GB
and other sources of noise etc., e.g. the number
of machines and other neighbouring
operations. Reliable workplace values may also
vary from country to country. With this
information the user should at least be able to
make a better assessment of the dangers and
risks involved.

7. Before starting the machine

Before you connect the appliance to the
mains supply make sure that the data on the
rating plate are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment
Unpack the saw and check it for damage
which may have occurred in transit.
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
All covers and safety devices have to be
properly fitted before the machine is
switched on.
It must be possible for the blade to run
freely.
When working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws, etc.
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the machine's moving parts run
smoothly.
8. Installation
Caution: Pull out the power plug before
carrying out any maintenance, alteration or
assembly work on the table circular saw.
8.1 Fitting the base frame (Fig. 4-10)
Turn the bench circular saw around and lay
it on the floor
Screw the four legs (18) loosely to the saw
with the short hex screws (d), washers (b)
and locking rings (a).
The legs (18) with the two holes which lie
one above the other on the underside must
20
13.05.2009 14:04 Uhr Seite 20
be mounted at the rear of the machine, so
that the holes are facing the rear. (Fig. 5)
Now fasten the longitudinal and cross struts
(19), as well as the middle struts (20)
loosely with the carriage bolt (f), washers (b)
locking rings (a) and nuts (c), to the legs.
The longitudinal struts are marked with "A",
the cross struts with "B". Screw the four
middle struts (20) to each other with the
screws (d), washers (b), spring rings (a) and
nuts (c) (Figs. 6-8)
Only screw the hex screws (d) and nuts (c)
loosely. Important: The longer struts must
be used on the sides.
Screw the stability bar (22) to the holes on
the rear legs (18) with 2 long hex screws
(e), washers (b), locking ring and nuts each
(c). (Figure 9)
Caution:
Both stability bars must be attached to
the rear side of the machine.
Now attach the rubber feet (21) to the legs
(18). (Figure 10)
Then screw all of the screws and nuts to the
base frame.
8.2 Attaching the table length and width
extensions (Fig. 11-15)
Loosely attach the table width and length
extensions (14/15) to the saw bench (1) with
the hex screws (d), locking rings (a),
washers (b) and nuts (c). (Figure 12-13).
Screw the supports (23) loosely to the
housing of the bench saw and to the table
width/length extensions. (Short supports for
width extension, long supports for length
extension) (Fig 14-15).
Adjust the table width and length according
to the saw bench (1).
Finally, tighten all screws.
Turn the saw and base frame around and
set it on the floor.
8.3 Attaching the splitter (Fig 16-17)
Caution: Pull out the power plug.
Set the saw blade (5) to max. cutting depth.
Adjust and lock the cutting depth into the 0°
position (see Fig 9.2)
Remove the table inserts (see 8.5)
Loosen the fixing screws (27).