Using The Machine - Stiga EW 330 Gebrauchsanweisung

4.1 UNPACKING (Fig.3.0)
1. Remove all the unassembled parts from the box.
2. Take out the machine and dispose of the box and
packaging in compliance with local regulations.
4.2 HANDLE ASSEMBLY
Install the RH (Fig.4.A) and LH (Fig.4.B) lower parts. Fit
the upper part of the handle (Fig.4.C) and apply the cable
clamp (Fig.4.D).
4.3 GRASS CATCHER ASSEMBLY (Fig.5.0)
5. CONTROLS
5.1 SWITCH COMMAND
The switch control starts/stops the engine and at the same
time engages/disengages the cutting means.
The positions shown correspond to:
Operation. To start the device, press the
safety button (Fig.6.A), pull one of the two
levers (Fig.6.B) and wait for 2-3 seconds for
the engine to start.
Stopping. The engine automatically stops
when both levers are released (Fig.6.B).
When the engine starts, the cutting
means is also engaged.
5.2 CUTTING HEIGHT ADJUSTMENT
Do this when the cutting means is stationary.
• Adjustment (See Fig.7.A/B/C)
Do not tilt the wheel axis during this operation,
so as to allow it to enter at the same time in one of the
available grooves.
6.

USING THE MACHINE

6.1 PRELIMINARY PROCEDURES
Place the machine in a stable horizontal position on the
ground.
6.1.1 Preparing the machine before starting work
a. Preparation for grass cutting and collection in the
grass catcher:
1. Lift the rear discharge guard (Fig.8.A) and hook the
grass catcher correctly, as indicated in the figure
(Fig.8.B).
6.1.2 Cutting height adjustment
Adjust the cutting height as indicated in (par. 5.2).
6.2 SAFETY CHECKS
Always carry out the safety checks before use.
6.2.1 Safety check before every use
• Check the integrity and the correct mounting
of all components of the machine;
• make sure that all fastening devices are correctly tightened;
• keep all surfaces of the machine clean and dry.
6.2.2 Machine operating test
Action
Start the machine (section
6.3 );
Result
The cutting means should
move.
Release the switch control
levers.
Test driving
If any of the results fail to match the indications
provided in the tables, do not use the machine! Contact
an Authorised Service Centre to have it checked and
repaired if necessary.
6.3 START-UP
NOTE Start up the machine on a flat surface without ob-
stacles or high grass.
1. Hook the extension cable correctly, according to the
indications (Fig.9.A).
2. FIRST connect the power cable plug to the extension
cable (Fig.9.B) and THEN the extension cable to the
mains socket (Fig.9.C).
3. To start the engine, press the safety button (Fig.9.D)
and pull the lever (Fig.9.E) of the switch.
6.4 OPERATION
IMPORTANT If the motor stops because it is overheated
whilst mowing, you must wait approximately 5 minutes be-
fore restarting it.
IMPORTANT When working, always keep a safe dis-
tance from the cutting means, given by the length of the
handle.
6.4.1 Grass cutting
1. Start moving forward and mowing the grass area.
2. Adjust the cutting height (par. 5.2) according to the
lawn conditions (grass height, density and humidity).
3. It is recommended to always cut at the same time in the
two directions (Fig.10.0), removing maximum 1/3 of the
height of the lawn (Fig.11.0).
6.4.2 Grass catcher emptying
For grass catcher with contents indicator device:
Lifted = empty
Lowered = full
During operation, when the cutting means is moving,
the indicator stays lifted as long as the grass catcher
can collect the cut grass; when it is lowered, it means
that the grass catcher is full and must be emptied.
To remove and empty the grass catcher:
Wait until the cutting means stops (Fig.12 A);
1.
2. Remove the grass catcher (Fig.12.B/C/D).
6.5 STOPPING THE MACHINE
After having stopped the machine, it will take a few
seconds for the cutting means to stop.
IMPORTANT Always stop the machine:
To stop the machine:
1. Release the switch control lever (Fig. 13.A).
2. Wait until the cutting means stops;
EN - 4
The engine must turn off
and the cutting means must
stop within a few seconds.
No abnormal vibrations.
No abnormal sound.