Pioneer PDP-LX608D Bedienungsanleitung Seite 83

Additional information
Problem
• Audio is output but no image is
presented.
• Images are presented but no
audio is output.
• Picture is cut off.
• Strange colour, light colour, dark
or colour misalignment.
• After-image lag.
• Brightness and colour tone on
both sides differ from those in the
centre in 4:3 mode.
HDMI Control
• HDMI Control functions do not
operate.
• No image and audio is
presented.
• No picture.
• No sound.
•An error message "The device
cannot be operated. Please check
the connection." appears.
Possible solution
• Check if you have selected "Picture Off" for "Energy Save". With this option selected, the screen
is deactivated: only sound is output. To restore the screen display, press any button other than
i + /i – or e. (See page 37.)
• Check if you have selected the minimum volume. (See page 22.)
• Check that no headphones are connected.
• Check that the sound is not muted. (See page 22.)
• When using "INPUT 5" as the input source, check that the audio terminal is also properly
connected. (See page 60.)
• When using PC as the input source, check that the audio terminal is also properly connected.
(See page 61.)
• When using "COMPONENT" for "INPUT 2", check to see if the settings are properly entered. (See
pages 52 and 58.)
• Is the image position correct? (See pages 51 and 52.)
• Has the correct screen size been selected? (See page 53.)
• Adjust the picture tone. (See pages 31 to 35.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the colour system setting. (See page 53.)
• After displaying a still image or a very bright image for a certain period of time, if the screen is then
switched to a darker scene, the previous image may appear as an after-image.
• This can be rectified by playing a rather bright moving image for several minutes. However, displaying
a still image for excessively long periods of time may cause permanent display deterioration.
• You can display the "Video Pattern" screen that helps eliminate after-image when it occurs. (See page 56.)
• If images in 4:3 mode or letterbox images are displayed for long periods or for shorter periods over
several days, an after-image may remain due to burning. This is a characteristic of plasma displays.
• We recommend that you enjoy watching images in a full screen mode as much as possible. (See
page 53.)
• We recommend you select "Auto" for "Brightness Sync." in the Side Mask setting. This adjusts the
brightness of the grey side masks according to the brightness of the main image. (See page 55.)
• Check if the connections are properly made between the plasma television and the device that
supports the HDMI Control functions. (See page 75.)
• Check if you have entered the settings properly for "HDMI Control Setting". (See page 77.)
• Check if the settings for the HDMI Control functions are effective on the connected device(s). For
details, refer to the operation manual that came with the device.
• Check if the connections are properly made between the plasma television and the device that
supports the HDMI Control functions. (See page 75.)
• Check if you have entered the settings properly for the HDMI Control Setting. (See page 77.)
• Check if you have selected "Enable" in "HD AV Converter" for "HDMI Control Setting" even though
no HD AV Converter is connected. Select "Disable" if that is the case. (See page 77.)
• Check that the HD AV Converter is connected to INPUT 4 if you have selected "Enable" in "HD AV
Converter" for "HDMI Control Setting". (See page 77.)
• Check if the connections are properly made between the plasma television and the device that
supports the HDMI Control functions. (See page 75.)
• Check if you have entered the settings properly for "HDMI Control Setting". (See page 77.)
• Check if the connections are properly made between the plasma television and the device that
supports the HDMI Control functions. (See page 75.)
• Check if you have entered the settings properly for "HDMI Control Setting". (See page 77.)
• Check if you have an HDMI controlled AV system connected to one HDMI terminal and the
recorder or player connected to another HDMI terminal on the plasma television. When
connected this way, audio out from the recorder/player does not go through the plasma television
SPDIF terminal resulting in no sound to the AV system. When using an AV system and recorder
or player, be sure to connect the recorder or player to the AV system input terminal.
• Check if the connections are properly made between the plasma television and the device that
supports the HDMI Control functions. (See page 75.)
• Check if you have entered the settings properly for "HDMI Control Setting". (See page 77.)
15
83
En