Werbung
RT600E SERIES ON RUBBER CAPACITIES (cont'd.)
PICK & CARRY CAPACITIES (UP TO 2.5 MPH) -
BOOM CENTERED OVER FRONT (See note 7)
Radius
in
Main Boom Length in Feet
Feet
33
30,150
30,150
10
(69.5)
(73.5)
30,150
30,150
12
(65.5)
(70.5)
29,650
29,650
15
(59.5)
(65.5)
22,650
22,650
20
(47.5)
17,850
17,850
25
(32)
13,100
30
(34.5)
35
40
45
50
55
60
Min. boom angle (° ) for indicated length (no load)
Max. boom length (ft.) at 0° boom angle (no load)
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
Lifting Capacities at Zero Degree Boom Angle
On Rubber - Pick & Carry
Main Boom Length in Feet
Boom
Angle
33
14,550
10,050
0°
(28.2)
NOTE: ( ) Reference radii in feet.
10
#9006
40
50
60
17,850
(77)
17,850
(74.5)
17,850
17,850
(71)
(75.5)
17,850
17,850
(57)
(64.5)
(70)
17,850
17,850
(47)
(58)
(65)
13,100
13,100
(50)
(59)
10,050
10,050
(41.5)
(53)
7,340
7,340
(30.5)
(46.5)
6,020
(38.5)
4,940
(28.5)
40
50
60
6,020
4,030
(35)
(45)
(55)
A6-829-100837A
NOTES TO ALL RUBBER CAPACITY CHARTS:
1. Capacities are in pounds and do not exceed 75% of
tipping loads as determined by test in accordance
70
with SAE J765.
2. Capacities are applicable to machines equipped
with 23.5x25 (20 ply) tires at 85 psi cold inflation
pressure.
3. Defined Arc - Over front includes 6° on either side
14,750
of longitudinal centerline of machine (ref. drawing
(78)
C6-829-003529).
14,750
(73.5)
4. Capacities appearing above the bold line are based
14,750
on structural strength and tipping should not be
(69.5)
relied upon as a capacity limitation.
13,100
5. Capacities are applicable only with machine on firm
(64.5)
level surface.
10,050
6. On rubber lifting with boom extensions not permit-
(60)
ted.
7,340
(54.5)
7. For pick and carry operation, boom must be cen-
6,020
tered over front of machine, mechanical swing lock
(49)
engaged and load restrained from swinging. When
handling loads in the structural range with capaci-
4,940
ties close to maximum ratings, travel should be
(43)
reduced to creep speeds.
4,030
(35.5)
8. Axle lockouts must be functioning when lifting on
3,260
rubber.
(26.5)
9. All lifting depends on proper tire inflation, capacity
0
and condition. Capacities must be reduced for
70
lower tire inflation pressures. See lifting capacity
chart for tire used. Damaged tires are hazardous to
safe operation of crane.
10. Creep - not over 200 ft. of movement in any 30
minute period and not exceeding 1 mph.
70
2,590
(65)
RT600E Series
Werbung
Kapitel
