Werbung
Verfügbare Sprachen
Verfügbare Sprachen
R R e e c c o o m m m m e e n n d d e e d d s s e e p p a a r r a a t t i i o o n n s s d d i i s s t t a a n n c c e e s s b b e e t t w w e e e e n n p p o o r r t t a a b b l l e e a a n n d d m m o o b b i i l l e e R R F F c c o o m m m m u u n n i i c c a a t t i i o o n n s s e e q q u u i i p p m m e e n n t t a a n n d d T T r r u u R R i i z z e e
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects, and people.
T T r r u u R R i i z z e e is suitable for use in the electromagnetic environment specified below. The customer or the user of T T r r u u R R i i z z e e
should assure that it is used in such an environment.
I I m m m m u u n n i i t t y y t t e e s s t t
Electrostatic discharge
(ESD)
IEC 61000-4-2
Electrostatic fast Transient/
burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, voltage
variations and short
interruptions on power
supply input lines
IEC 61000-4-11
Power frequency (50/60Hz)
magnetic field
IEC 61000-4-8
EN
24
0.38
1.2
3.8
12
G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y
I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l
+8 kV contact
+15 kV air
+2 kV for power supply lines
+1 kV for input/output lines
+1 kV line(s) to line(s)
+2 kV line(s) to earth
0% U
for 0.5 cycles at 0°,
T
45°, 90°, 135°, 180°, 225°,
270°, and 315°
0% U
for 1 cycle
T
70% U
(30% dip in U
T
25 cycles
0% U
for 25 cycles
T
30 A/m
0.38
1.2
3.8
12
C C o o m m p p l l i i a a n n c c e e l l e e v v e e l l
+8 kV contact
+15 kV air
+2 kV for power supply lines
+1 kV for input/output lines
+1 kV line(s) to line(s)
+2 kV line(s) to earth
0% U
for 0.5 cycles at 0°,
T
45°, 90°, 135°, 180°, 225°,
270°, and 315°
0% U
for 1 cycle
T
) for
70% U
(30% dip in U
T
T
25 cycles
0% U
for 25 cycles
T
30 A/m
0.73
2.3
7.3
23
E E l l e e c c t t r r o o m m a a g g n n e e t t i i c c
e e n n v v i i r r o o n n m m e e n n t t - - g g u u i i d d a a n n c c e e
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Mains power quality should
be that of a typical
commercial or hospital
environment.
Mains power quality should
be that of a typical
commercial or hospital
environment.
Mains power quality should
be that of a typical
commercial or hospital
environment. If the user of
T T r r u u R R i i z z e e requires continued
operation during power
main interruptions, it is
) for
T
recommended that the
device be powered from an
uninterrupted power supply
or a battery.
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
3333-009-005 Rev C.0
Werbung
