Safety Instructions For Batteries; Technical Data - REMS Nano Betriebsanleitung

g

Safety instructions for Batteries

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
Only use the battery in the REMS power tool. Only then is the battery safe
from dangerous overloading.
plate. Using other batteries can lead to injuries and risk of re due to exploding
batteries.
Only recharge REMS batteries in the REMS rapid charger. There is a risk of
re if an unsuitable battery charger is used.
Charge the battery to full capacity with the rapid charger before using for
Batteries are delivered partly charged.
There is a risk of bending the battery contacts and damaging the battery.
a risk of explosion and re.
There is a risk of explosion and re.
and re due to short-circuiting.
to or improper use of the battery can cause fumes to escape. The fumes can
irritate the respiratory tracts. Let in fresh air and consult a doctor in case of
symptoms.
Leaking uid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the uid gets into the eyes.
Observe the safety instructions on the battery and the rapid charger.
There is a risk of explosion and re due to short-circuiting.
Protect the battery contacts against short-circuiting, e.g. with a cap.
defective batteries over to an authorised REMS contract service workshop or a
recognised disposal company. Observe the national regulations.
WARNING Danger with a medium degree of risk which could result in death
or severe in ur (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor in ur
(reversible) if not heeded.
NOTICE
Material damage, no safet note! No danger of in ur .
Read the operating instructions before use
REMS Nano complies with protection class I
REMS Akku-Nano and rapid charger compl
with protection class Il
Environmentall friendl disposal
CE conformit mark

1. Technical Data

Use for the intended purpose
WARNING
REMS Nano and REMS Akku-Nano are intended for the purpose of cutting pipes.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
REMS Nano: Electric pipe cutting machine (without cutting wheel),
single open-ended wrench size 8, operating instructions,
carr ing case.
REMS Akku-Nano: Cordless pipe cutting machine (wi hout cutting wheel),
Li-Ion batter , Li-Ion/Ni-Cd rapid charger, single
open-ended wrench size 8, operating instructions,
carr ing case.
1.2.
REMS Nano
REMS Akku-Nano
REMS High-Power-Batter Li-Ion 10.8 V, 1.3 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules 3B
8
REMS Herkules Y
REMS Jumbo
REMS Jumbo E
Carr ing case
REMS CleanM
1.3. Application Area
REMS Nano, REMS Akku-Nano:
Pipes of press tting s stems made of
1.4. Speed
REMS Nano, REMS Akku-Nano:
Idle speed of cutting wheel
1.5. Electrical Data
REMS Nano:
230 V~; 50 – 60 Hz; 130 W
Fuse (mains) 10 A (B), cut-out operation S3 20 % AB 2/10 min,
There is
radio interference suppressed, protection class I, PE conductor as of
machine no. 3650
REMS Akku-Nano: 10,8 V =, 16 A, 270 W
Rapid-charger
There is a risk of explosion
Li-Ion/Ni-Cd
Damage
1.6
REMS Nano:
L × W × H:
REMS Akku-Nano:
L × W × H:
1.7. Weights
REMS Nano
REMS Akku-Nano drive machine without batter
1.8. Noise Data
Hand the
Workplace-related emission
value
1.9. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used b wa of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminar evaluation of the exposure.
The indicated weighted effective value of acceleration can differ during opera ion
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual condi ions of use (periodic dut ) it ma be necessar
to establish safet precautions for he protection of the operator.
2. Start-up
2.1. Electrical Connection
Caution: Mains voltage present! Before connecting the electric pipe cutting
machine or the rapid charger, check whether the voltage given on the rating
plate corresponds to the mains voltage. Onl use sockets/extension leads with
a functioning protected earth contact for REMS Nano. On building sites, in a
wet environment, indoors and outdoors or under similar installation conditions,
onl operate the electric pipe cutting machine on the mains with a fault current
protected switch (FI breaker) which interrupts the power suppl as soon as the
leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries
NOTICE
Alwa s hold the batter (9) upright when inserting it in the drive unit or the rapid
charger. If inserted at an angle it can cause damage to he contacts and result
in a short circuit which damages the batter .
Total discharging by undervoltage
The Li-Ion batteries ma not drop below a minimum voltage because otherwise
the batter could be damaged b "total discharge". The cells of the REMS Li-Ion
batter are delivered pre-charged to approx. 40 %. Therefore he Li-Ion batteries
must be charged before use and recharged regularl . Failure to observe this
regulation of the cell manufacturer can lead to damage to the Li-Ion batter b
844000
total discharging.
844001
844510
Total discharging due to storage
571560 If a relativel low charged Li-Ion batter is stored, self discharging can lead to
844050 total discharge damage of the batter after longer storage. Li-Ion batteries must
844051
therefore be charged before storing and recharged ever six months at the
120120 latest and charged again before use.
stainless steel, C-steel (not jacketed)
semi-hard and hard copper
composite pipes
Input 230 V~; 50 – 60 Hz; 65 W, protection class II
Output 10,8 – 18 V – ---
Input 100 – 120 V~; 50 – 60 Hz; 65 W, protection class II
Output 10,8 – 18 V – ---
L = 78 dB L
wA
CAUTION
WARNING
g
120130
120200
120240
574436
140119
Ø 12 – 28 mm
Ø 10 – 35 mm
Ø 10 – 40 mm
130 min
405 × 90 × 103 mm (15 9"× 3.5"× 4")
408 × 88 × 105 mm (16"× 3.4"× 4.1")
1.9 kg (4.2 lb)
2.0 kg (4.4 lb)
= 67 dB L = 87 dB K = 3 dB
pA pC, peak
1.2 m/s² K = 1.5 m/s²