Herunterladen Inhalt Inhalt Diese Seite drucken

Introduction; Please Observe The Following; Device Description (Fig. 1-18, 24) - Scheppach Parkside PMTS 210 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Application other than specified
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113

Please observe the following:

Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. They must be read and carefully observed by all
operating personnel before starting the work.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The required minimum
age must be observed.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such ma-
chines must also be observed.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.

3. Device description (fig. 1-18, 24)

1.
Saw table
2.
Transverse stop
3.
Riving knife
4.
Saw blade guard
4a. Wing nut (saw blade guard)
4b. Carriage bolt (saw blade guard)
5.
Saw blade
6.
Table inlay
7.
Parallel stop, complete
8.
Hand wheel
9.
Locking handle
10. Overload switch
11. On/off switch
12. Rubber foot
13. Tool hook
14. Push stick
15. Locking knob
15a. Clamping plate
16. Holder
16a. Screw (parallel stop)
17. Stop rail
18. Knurled screw (transverse stop)
19. Turning handle
20. Ring spanner, 7/8 mm
21. Ring spanner, 19/10 mm
22. Table width extension
23. Guide tube
24. End piece
25. Screw (end piece)
26. Knurled screw (table width extension)
27. Guide bushing
28. Height adjustment screw
29. Lock nut
30. Support foot
31. Hole (riving knife)
32. Screw (table inlay)
33. Fixing screw (riving knife)
34. Screw (saw blade cover)
35. Saw blade cover
36. Suction port
37. Groove (stop rail)
38. Scale
39. Groove (stop rail)
40. Groove (saw table)
41. Mains cable
42. Bracket for workbench mounting
43. Screw (self-tapping)
44. Washers
GB/IE
19

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis