Cleaning And Maintenance - Scheppach 5902205901 Originalbetriebsanleitung

The set angle can be read off the scale (B). Secure
the parallel stop (5) with the star grip nut (22) again
after making the setting.
9.1.2 Surface planing mode (fig. 9/10)
Attention! Watch out the right mounting of the chip
extractor (point 8.3)
• (Narrow workpieces, see fig. 9) Open the clamp-
ing screw (9) and move the planing knife cover (7)
only so far as the workpiece is wide.. Then tighten
the clamping screw (9) again.
• (wide, flat workpieces see fig. 10) Open the
star grip nut (6) and set the planing blade cov-
er cpl (13) just as high as the workpiece is thick.
The planer blade cover (7) covers the entire knife!
Tighten the star grip nut (6) again.
• Plug in the machines power cord. Press the green
button "I" to start the planing machine.
• Place the workpiece you wish to plane on the feed
table (12). Slide the workpiece as far as possible
with the push stick (16) forwards towards the plan-
ing table (26) over the knives (24).
• When you have finished work, switch off the ma-
chine. To do this, press the red button "0". Then
disconnect the machine from the mains supply.
• Remove the chips and dust from the feed table
(12), planing table (26) and knife block after the
machine has reached a complete standstill.
• Bring back the planer blade cover (7) and cover
the planer blade over its entire length.
9.2 Thicknessing
m IMPORTANT!: Pull out the power plug before
performing any maintenance, cleaning and adjusting
work.
9.2.1 Adjustment (fig. 4/11)
Place the crank handle (10) on the spindle (19) and
turn it to adjust the thicknessing table (21) to the re-
quired height. The set angle can be read off the scale
(C).
9.2.2 Thicknessing mode (fig. 4/11/12)
Attention! Watch out the right mounting of the chip
extractor (point 8.4)
• Plug in the machines power cord. Press the green
button "I" to start the plane.
• Place a workpiece on the thicknessing table (21).
Guide the workpiece towards the feed table (12).
• When you have finished work, switch off the ma-
chine. To do this, press the red button "0". Then
disconnect the machine from the mains supply.
• Remove the chips and dust from the thicknessing
table (21) and knife block after the machine has
reached a complete standstill.
32 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
9.3 Changing the knives (fig. 13/14)
• m IMPORTANT!: Always pull the mains plug be-
fore changing the knives.
• Pull the planing knife cover (13) forwards as far as
possible so that the entire knife block is exposed.
• Release and remove the four knife clamping
screws (23).
• Lift the knives (24) and knife block (27 from the
cutter block.
• Remove the chips and any resin from the cutter
block and knife support.
• Place new knives (24) into the cutter block and fix
them with the rectangle slots in both screw heads.
(With these two screws, height-adjustment of the
knife is done.)
• Place the knife block (27) onto the knife (24).
• Slightly tighten the four clamping bolts (23).
• Repeat these actions for the second knife (24).
• Then adjust the planer/thicknesser knives (24) ex-
actly with the output table. Use a ruler that you put
onto the output table.
• By the two set screws (31), the knife (24) can be
adjusted for height.
• By turning the cutter block and using the ruler, you
can see the height adjustment.
• The knife is exactly set, when the ruler is moved
by the knives not higher than 3 mm.
• After a successful knife setting, all clamping
screws must be tightened (8.4 N/m).
Please mind:
• Sharp planer/thicknesser knives guarantee a clean
planing surface and put less stress on the motor.
• After three grinding actions, a maximum materi-
al removal of 3 x 0.05 mm may not be exceeded.
• The planer/thicknesser blades used on this ma-
chine are not suitable for rebating and dovetailing.
• Finally lower the cutter block guard again onto the
table. Cover the cutter block and block it with the
star grip screw.
m IMPORTANT!
Only use knives which are recommended by the
manufacturer for this equipment. If you use other
knives there is a risk of injuries due to lack of control.
Avoid over-tightening and the possibility of the thread
becoming detached. If the latch or the screws have
worn out threads they must be immediately replaced.

10. Cleaning and maintenance

m IMPORTANT! Before any cleaning, adjustment,
maintenance or repair work, disconnect the power
plug from the main power supply!
Machine care
The planer/thicknesser requires little maintenance.
The ball bearings are permanently lubricated.