Cleaning, Maintenance And Ordering Spare Parts - Scheppach PLM1800 Original Bedienungsanleitung

The mains connection at the customer's work place
and the extension cable used must correspond to
these regulations.
Faulty electrical connecting leads
Insulation damage often occurs at electrical connect-
ing leads.
Causes include:
• Pressure marks caused when connecting leads
are run through windows or the cracks of doors.
• Folds caused by the improper attachment of run-
ning of the connecting leads.
• Cutsresulting from the crossing of the connecting
lead.
• Insulation damages caused by the ripping out of
the connecting lead from the wall socket.
• Cracks due to the ageing of the insulation.
Faulty electrical connecting leads such as these may
not be used and are highly dangerous due to the in-
sulation damage.
Check electrical connecting leads regularly for dam-
age. Ensure that the connecting lead is not attached
to the mains supply when you are checking it.
Electrical connecting leads must correspond to the
relevant VDE and DIN regulations. Only use con-
necting leads with the code H05VV-F.
The type designation must be printed on the con-
necting lead by regulation.
With a single-phase a.c. motor, we recommend a C
16A or K 16A fuse for machines with a high start-up
current (from 3000 Watt)!
13. Cleaning, maintenance and or-
dering spare parts
General maintenance measures
Wipe chips and dust off the machine from time to
time using a cloth. In order to extend the service life
of the tool, oil the rotary parts once monthly. Do not
oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
m WARNING! Pull out the power plug before performing
any maintenance, cleaning and adjusting work.
13.1 Cleaning
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub
the device clean with a clean cloth or blow it off
with compressed air at low pressure.
• We recommend that you clean the device directly
after every use.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can
penetrate the device interior. Water penetrating an
electrical device increases the risk of an electric
shock.
• Clean the chip ejection and/or dust extraction on a
regular basis.
• Do not spray the device with water!
13.2 Maintenance
13.2.1 Machine (fig. 21+22)
Periodically lubricate the following parts about every
10 operating hours:
• Anti-return claws (42)
• Threaded rod for adjusting the height of the planer
(43)
• Guide columns for height adjustment (44)
Use only dry lubricant.
The feed table, discharge table, planing table, feed/
discharge rollers and anti-return claws must always
be kept free from resin. Soiled feed/discharge rollers
or anti-return claws must be cleaned. To prevent the
motor from overheating, dust that settles in the venti-
lation openings must be removed on a regular basis.
Improve the sliding capability of the table by periodi-
cally treating it with a lubricant.
13.2.2 Cutting tool
Blade, terminal strip and planing shaft must be kept
free from resin. Clean these with an appropriate res-
in remover.
13.3 Ordering spare parts::
Please provide the following information when order-
ing spare parts;
• Device type
• Device article number
• Device ID number
• Spare part number of the required spare part
Repairs and work that has not been described in
these instructions may only be carried out by quali-
fied specialists.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*:
• V-belt
• Carbon brushes
• Planing blade
• Push stick
• Rubber rollers
* Not necessarily included in the scope of delivery!