Saeco HD8919 Bedienungsanleitung Seite 25

Behaviour
It is impossible to remove
the brew group.
It is impossible to insert the
brew group.
Coffee has too little cream
or is watery.
Coffee is leaking from the
coffee dispensing spout.
Coffee is not hot enough.
The machine grinds the
coffee beans, but coffee does
not come out.
Coffee comes out slowly.
The frothed milk is too cold. Cups are cold.
Milk does not froth.
Cause
The brew group is
positioned.
The coffee grounds drawer is in place. Remove the coffee grounds drawer before removing
The brew group is not in the idle
position.
The gearbox is incorrectly positioned. Place the drip tray and coffee grounds drawer in their
Grinders are set to a coarse position. Adjust the grinding fineness as described in the "5.3.3
The blend is not right, coffee is not
freshly roasted or is ground too coarse.
The machine must perform the self-
adjustment.
The coffee dispensing spout is clogged. Clean the coffee dispensing spout and its holes using
Cups are cold.
The temperature is
regulated.
Water empty.
The brew group is dirty.
The circuit is not primed.
The coffee dispensing spout is dirty.
The machine must perform the self-
adjustment.
Coffee is ground too finely.
The circuit is not primed.
The brew group is dirty.
The machine must perform the self-
adjustment.
The milk carafe is dirty or incorrectly
placed.
The milk carafe dispensing spout has
not been opened correctly.
The milk carafe is incompletely
assembled.
The type of milk used is not suitable
for frothing.
incorrectly Close the service door. Turn the machine off and back
on again. Wait for the 'Ready for brewing' signal and
then remove the brew group.
the brew group.
Make sure that the brew group is in the idle position as
described in the "7.2.1 Weekly brew group cleaning cycle"
chapter, "Reassembly phase".
proper seats. Close the service door. Turn the machine
on without the brew group. The gearbox goes back
to the correct position. Turn the machine off and put
the brew group in place following the instructions in
the "7.2.1 Weekly brew group cleaning cycle" chapter,
"Reassembly phase".
Ceramic coffee grinder adjustment" chapter.
Change coffee blend or adjust the grinding fineness
as described in the "5.3.3 Ceramic coffee grinder
adjustment" chapter.
Brew a few cups of coffee.
a toothpick.
Warm the cups with hot water.
Adjust the temperature as described in the "5.3.4
incorrectly
Brewing temperature adjustment" chapter.
Fill the water tank and prime the circuit again as
described in the "5.2.1 Water circuit priming" chapter.
Clean the brew group as described in the "7.2.1 Weekly
brew group cleaning cycle" chapter.
Prime the circuit as described in the "5.2.1 Water circuit
priming" chapter.
Clean the coffee dispensing spout and its holes using
a toothpick.
Brew a few cups of coffee.
Change coffee blend or adjust the grinding as described
in the "5.3.3 Ceramic coffee grinder adjustment" chapter.
Prime the circuit as described in the "5.2.1 Water circuit
priming" chapter.
Clean the brew group as described in the "7.2.1 Weekly
brew group cleaning cycle" chapter.
Brew a few cups of coffee.
Warm the cups with hot water.
Clean the carafe as described in the "7.4.3 Weekly
cleaning of the milk carafe components" chapter, and
insert it in the machine as shown in the "6.2 Milk carafe"
chapter, "Inserting phase".
Check that the milk dispensing spout has been correctly
removed as described in the "6.2 Milk carafe" chapter,
"Start up phase".
Check that all the components have been assembled
correctly, as described in the "7.4.3 Weekly cleaning of
the milk carafe components" chapter, "Reassembly phase".
Read the "6.3 Milk- and coffee-based preparations"
chapter.
Action
ENGLISH
21