Inhaltszusammenfassung für JB-Lighting Varycolor 2000
Seite 1
Varycolor 2000 Made in Germany by JB-lighting Version 2.00 JB lighting, Sallersteigweg 15, 89134 Blaustein, Tel: 07304 9617-15, Fax: 07304 9617 99...
Varycolor 2000 Vorwort Sie haben sich für den Kauf des Varycolor 2000 von JB-lighting entschieden. Vielen Dank für das entgegengebrachte Vertrauen. Der Varycolor 2000 gibt Ihnen viele Möglichkeiten, Ihre gewünschten Effekte zu realisieren. Lesen Sie zuerst in aller Ruhe diese Bedienungsanleitung durch, denn sie enthält Informationen, die Ihnen gewährleisten, Ihren Varycolor voll zu nutzen.
Varycolor 2000 Auspacken der Varycolor 2000 - Anlage Vor Ihnen befindet sich Ihre komplette Varycolor 2000 - Anlage Entnehmen Sie zuerst alle Teile aus den Kartons. Prüfen Sie, ob alle Teile in der Lieferung enthalten sind. • Varycolor 2000 •...
1. Varycolor 2000 aufstellen Stellen Sie Ihren Varycolor 2000 entweder auf eine feste Unterlage oder hängen Sie den Varycolor 2000 an dem dafür vorgesehen Bügel auf. Achten Sie auf jeden Fall darauf, daß sämtliche Lüftungsschlitze frei sind. 2. Varycolor verkabeln Die Verkabelung führen Sie wie folgt durch:...
Varycolor 2000 3. Grundeinstellungen am DIP-Schalters Alle DIP-Schalter "OFF": Testmodus (alle Funktionen des Varycolor 2000 laufen durch) DIP-Schalter 10 "OFF" Reset über DMX aus DIP-Schalter 10 "ON" Reset über DMX on (DMX-Wert 255 auf Gobokanal) Einstellen der DMX-Adressen am DIP-Schalter Ihr Varycolor verwendet 6 DMX-Kanäle, deshalb müssen Sie die DMX-Adressen in 6er-...
Seite 14
Varycolor 2000 Varycolor Nr. DMX-Adresse Schaltereinstellung - 14 -...
Varycolor 2000 Bestimmung der DIP-Schaltereinstellung für bestimmte DMX-Adressen Die einzelnen DIP-Schalter entsprechen den oben angezeigten Werten. Soll nun eine bestimmte DMX-Adresse eingestellt werden, so muß diese nur aus den einzelnen Werten zusammengezählt werden.(Immer größtmögliche Werte verwenden) Beispiel: DMX-Adresse "45" 32 + 8 + 4 + 1...
Öffnen Sie an der Oberseite des Varycolor 2000 die zehn Kreuzschlitzschrauben. und heben Sie den Deckel ab. Sie finden die Temperatursicherung in der hinteren Hälfte des Varycolor 2000. Die Temperatursicherung ist durch einen (weißen) Silikonschlauch geschützt und mit einem Ende in der Drossel festgeschraubt.
Varycolor herausdrehen. 1. Reinigung aller optischen Teile Sie sollten in regelmäßigen Abständen die optischen Teile des Varycolor 2000 reinigen um wieder die maximale Helligkeit des Farbwechslers herzustellen. Nachdem Sie das Gehäuse wie oben beschrieben geöffnet haben nehmen Sie ein fusselfreies Tuch und etwas Fensterputzmittel und reinigen Sie die Filter auf dem Farb- bzw.
Geräte hintereinander adressiert; d.h. das Erste verwendet die ersten sechs Adressen (gilt für ein Gerät mit sechs Kanälen) und das Zweite verwendet die nächsten sechs Adressen (Gerät mit sechs Kanälen) der 512 DMX-Adressen (Beispiel Varycolor siehe Seite13) Kanalbelegung Varycolor 2000 1. Varycolor 2000 6 Kanäle Kanal 1 frei Kanal 2...
Achten Sie auf die Polarität des Eproms!! (Die Einbuchtung am Eprom muß in die gleiche Richtung zeigen wie die Einbuchtung an der IC-Fassung) Bauen Sie nun Ihren Varycolor 2000 wieder zusammen. Stecken Sie nun Ihren Varycolor ein und testen Sie bitte alle Funktionen. - 22 -...
You decided to buy a Varycolor 2000 by JB-lighting. Thanks a lot for your confidence in our products. With the Varycolor 2000 you have many facilities to realize desired effects. First of all read through the operating instructions very calmly, because they contain informations that will guarantee an entire use of your Varycolor.
Plan of Current Circuits for Varycolor 2000 Occupation of Connector Rows and Jumper Changing of Eprom/ Software Update List of Pieces for Electronic Card of Varycolor 2000 Plan of Electronic Part for Electronic Card Plan of Current Circuits for Electronic Card...
Varycolor 2000 Unpacking of Varycolor 2000 Equipment Before you, you find the complete Varycolor 2000 equipment. First of all take all parts from the carton. Check, if the delivery contains all parts. • Varycolor 2000 • Powercord without plug • these operating instructions Should you notice a damage through transportation, please immediately inform the carriers respectively your dealer.
Starting the Equipment 1. Set up of Varycolor 2000 Either set up your Varycolor 2000 on a steady base or hang up your Varycolor 2000 from the bow assigned for. Take care that in any case all slits for ventilation are clear.
Varycolor 2000 Adjustment of DMX-Addresses at the DIP-Switch Your Varycolor 2000 is working in a 6 channel drive mode. The DIP-switch adjustment has to follow in 6 steps. Varycolor No. DMX-address DIP-switch position - 35 -...
Seite 36
Varycolor 2000 Varycolor No. DMX-address DIP-switch position - 36 -...
Varycolor 2000 Definition of DIP-Switch Positions for Defined DMX-Addresses Every single DIP-switch responds to the above designated figures. If you would like to adjust a defined DMX-address, you have to add up the single figures to get it. (Always use the highest figures as possible) For example: DMX-address "45"...
Warning: Before opening the appliance pull out mains plug! Loosen the ten screws on top of the Varycolor 2000 and lift the lid. In the back part of the Varycolor 2000 you find the overheat protection. This overheat protection is protected by a white silicon tube and with one end it is fixed in the ballast.
Open the casing by turning out the ten screws at the top of your Varycolor. 1. Cleaning of all optical parts You should clean the optical parts of your Varycolor 2000 periodically to restore maximum brightness of the varycolor. After having opened the casing as explained above, take a fuzz- free rag and a detergent for windows and clean the dichroic filters on the colour wheel and the effectwheel.
6 channels), for the second one the next 6 addresses (appliance with four channels) of all the DMX-addresses are used (see for example Varycolor p.35) Occupation of channels for varycolor 2000 Channel 1 = free Channel 2 = free...
Change of Eprom/ Software Update To change the Eprom proceed as follows: Open the lid of Varycolor 2000. Now remove the right side-piece with the electronic card. Remove the cover sheet for the electronic card by taking out the 4 screws (see sketch page 31).