Motor Protection; Care & Cleaning - Vita-Mix MIX'N MACHINE Advance Bedienungsanleitung

FOOT CONTROL OPERATING INSTRUCTIONS
Before using the Foot Control, follow the Installation Instructions
included with the Foot Control package.
WARNING!
TO AVOID RISK OF INJURY, DO NOT crimp, damage or replace
interconnecting air hose. DO NOT remove foot pedal activator from
protective shroud.
120V and 100V Models*
Turn power switch
o operate with foot pedal:
to the ON (I) position (Fig. A). Apply pressure to
the foot pedal to turn the mixer on (Fig. C).
Release pressure to turn mixer off. Turn power
switch to the OFF (O) position when not in use.
The Mix'n Machine is equipped with a reset breaker mounted on the
motor enclosure.
Should the motor be kept from turning (locked rotor) or otherwise be
overloaded, the breaker will trip. If this occurs, make sure the motor is free
Permanent Agitators
1. Fill a durable square or rectangular container to within 1 in. / 3 cm from
the top with hot (110˚F / 43˚C) water containing mild liquid detergent
(1 oz. per qt. / 30 ml per Ltr.). The container must be deep enough to
submerge the entire agitator and the shaft.
2. Hold the container all the way up around the agitator and shaft, to the
bottom of the motor chamber, and turn the machine on. Run for about
15 seconds. Repeat several times. Make sure all portions of the shaft
which contact food have been submerged. (Moving Splash Guard must
be removed for this cleaning operation.)
3. Repeat step 2, except use rinse water.
4. Repeat step 2, except use an approved 100 ppm sanitizing solution and
cleaner and run agitator and shaft under solution for a minimum of two
minutes.
5. Resanitize at the start of the day.
Removable/Reusable Agitator
1. Remove agitator from machine. Wash in warm soapy water.
2. Rinse clean.
3. Sanitize as necessary.
4. Dry and reassemble. NOT
commercial dishwasher heat may slightly bend the removable agitator
which could cause unbalance when blending.
Housing
1. Unplug the machine.
2. Remove the Splash Guard and wash in warm soapy water. Rinse clean
and sanitize as necessary. DO NOT
towels which would scratch the surface. Also avoid cleaners which
contain ammonia (most window cleaners contain ammonia).
recommended for dishwashers.
OFF
ON
Fig. A

MOTOR PROTECTION

CARE & CLEANING
recommended for dishwasher. Excessive
use any abrasive material or paper
220V Models*
o operate with foot pedal:
switch to the FOOT PEDAL (
B). Apply pressure to the foot pedal to turn
the mixer on (Fig. C). Release pressure to turn
mixer off. Turn power switch to the OFF (O)
position when not in use.
*The Foot Control cannot be used with the
M
Mix'n Machine Advance Programmable
models.
to rotate and wait a short period for it to cool down before pushing the
reset breaker and restarting the motor. Never remove or bypass the reset
breaker.
Countertop Models only:
sides until clear of the top pivot pins and pull the guard out. To mount
the Splash Guard, squeeze the sides and place onto the top pivot pins.
The guard should sit on the bottom pivot pins.
Wall Mount Models only:
squeeze the travel rods together and slide the guard down. To mount
the moving Splash Guard, slide the Splash Guard up over the rods until
they snap in place. To clean the travel rods, wipe with a damp cloth.
remove the rods from the mixer.
NOT
3. All stainless steel surfaces may be cleaned and disinfected with a
commercial cleaning solution. However,
other fluids into the motor chamber.
the switches, motor protector, or cord entry hole. Abrasive cleaners may
leave noticeable changes in the surface finish. Make sure all areas in
and around the motor enclosure and machine are dry before plugging
the machine back in.
4. Switches may become sticky from use. Unplug the machine and use a
damp cloth, moistened with water and a mild detergent, to clean
around the edges of the switch paddles until they function freely. Work
the switches back and forth a few times to loosen any dried residue
under switch. Leaving switches sticky will damage or burn out the
switches. Clean carefully, using caution not to allow water or other
liquids to infiltrate the switch. Dry with a soft cotton cloth. Make sure
switches are dry before plugging the machine back in.
IMPORTANT NOTES
CLEANING AND SANITIZING PRODUCTS:
• use abrasive cleaning agents or concentrated bleach when
DO NOT
cleaning.
• use any cleaners containing Quatinary Sanitizers on polycarbonate
DO NOT
components.
NOT
• Follow cleaner/sanitizer manufacturer's specifications and instructions.
• Local codes should be followed for cleaning/sanitizing equipment.
5
Turn power
ON
) position (Fig.
OFF
Foot Pedal
Fig. B
Fig. C
To remove the Splash Guard, squeeze the
To remove the moving Splash Guard,
spray any water or
DO NOT
use excess liquid around
DO NOT
DO