Scheppach TKU Bedienungsanleitung Seite 12

• Check all power supply lines. Do not use defective lines.
• Keep children away from the machine when it is con-
nected to the power supply.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may not be diverted
from their work.
• The machine must be equipped with a table length ex-
tension if a second person is work.ing at the circular
sawbench removing cut work.pieces. The second person
may not stand anywhere else but at the take-off table
end.
• The working space on the machine must be free of chips
and wood scrap.
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
• Pay attention to the rotational direction of the motor and
tool - see Electrical Connection.
• The safety mechanisms on the machine may not be re-
moved or rendered unusable.
• Cleaning, changing, calibrating, and setting of the
machine may only be carried out when the motor is
switched off. Pull the power supply plug and wait for the
rotating tool to completely stop.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• The machine must be attached to a scheppach dust ex-
tractor during all work. cycles. Please observe the proper
use of this.
• When working on the machine, all safety mechanisms
and covers must be mounted.
• Use only sharpened, nick-free and non-deformed saw
blades.
• Circular saw blades made from superspeed steel may
not be used.
• The splitting wedge is an important safety feature. The
work.piece is fed through the splitting wedge, which
prevents the cut from closing behind the saw blade and
also prevents the workpiece from kicking back.
• Lower the cover onto the work.piece during every work.
ing operation. It must stand horizontal above the saw
blade.
• Always use a push-stick for longitudinal cuts of narrow
work pieces less than 120 mm). The push-stick must
be used to prevent you from having to work. with your
hands near the sawblade. Stop the machine to repair
a failure or remove pieces of wood which have become
jammed. Disconnect the mains plug.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• The table insert must be renewed when the saw slot is
wom down. Pull power supply plug.
• Before the machine is put into operation it must be con-
nected to a dust extractor with a flexible, non-flammable
suction hose. The suction should switch on automati-
cally when the machine is switched on.
• When leaving the work place, switch the motor off. Pull
the power supply plug.
• Cut off the extemal power supply of the machine or plant
even if only minor changes of place are envisaged. Prop-
erly reconnect the machine to the supply mains before
recommissioning.
• Connection and repair work. on the electrical installation
may be carried out by a qualified electrician only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
9 9
Use only as authorized
• The machine corresponds to the valid EC guideline.
• The scheppach TKU circular sawbench is defined as a
semi-stationary machine in accordance with pr EN 1870-
1.
• If an original scheppach base is not used, the machine
must be placed firmly upon a stable stand resembling a
table. The working height should be 850 mm.
• The machine's workstation is in front of the machine to
the left of the sawblade.
• The machining range and surrounding areas of the ma-
chine must be clear of interfering foreign matter to pre-
vent accidents occurring.
• Workpieces must be completely free of foreign objects,
i.e. nails or screws.
• Before the machine is put into operation it must be con-
nected to a dust extractor with a flexible, non-flammable
suction hose. The suction should switch on automati-
cally when the machine is switched on.
• When used in enclosed rooms, the machine must be
connected to a vacuum exhaust unit.
Use the scheppach dust extractor ha 3200 or ha 2600 to
remove matchwood or saw dust. The vacuum support flow
rate must be 20 m/s. Subatmospheric pressure 1200 Pa.
• The scheppach automatic switching unit is available as a
special accessory.
• Type ALV 2 Art. No. 7910 4010
• Type ALV 10 Art. No. 7910 4020
• The vacuum exhaust unit automatically switched on af-
ter a 2-3 second delay after the machine tool is turned
on. This avoids overtoading the circuit fuse. After tuming
off the machine tool, the vacuum exhaust unit remains
on for an additional 3-4 seconds and is then automati-
cally switched off. Remaining dust is thereby removed
by vacuum exhaust, as required by German regulations
governing hazardous materials. This results in savings
in electricity consumption and reduces noise levels, as
the vacuum exhaust unit is on only during machine tool
operation.
• For work in commercial spaces, the scheppach dust ex-
tractor woova 7 must be used.
• Do not remove or shut off vacuum exhaust systems or
dust removers while machine tools are operating.
• The scheppach circular sawbench is designed exclusively
for the machining of wood and materials similar to wood.
Only original scheppach tools and accessories may be
used. Use the required sawblade in accordance with the
EN 847-1 norm depending on the type of cut and type
of wood (solid wood, plywood or chipboard). Please ob-
serve the scheppach Special Tool Accessories.
• The machine must only be used in technically perfect
condition in accordance with its designated use and the
instructions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in operating the machine. Any functional
disorders, especially those affecting the safety of the
machine, should therefore be rectified immediately.
• Relevant accident prevention regulations and other, gen-
erally recognized safety-technical rules must also be ad-
hered to.
• The scheppach machine may only be used, maintained,
and operated by persons familiar with it and instructed
in its operation and procedures. Arbitrary alterations to
the machine release the manufacturer from all responsi-
bility for any resulting damages.
230 V/50 Hz
400 V/230 V/50 Hz