Rear Panel; Installation; Rack Installation - Omnitronic MCP-8150 Bedienungsanleitung

Rear panel

MCP-8150
CH 8
BRIDGE
2 1 2 1
3 3
1=shield 1=shield
2=+Life 2=+Life
3= - Life 3= - Life
FILTER FILTER
BYPASS BYPASS
LOWPASS LOWPASS
HIPASS HIPASS
LEVEL LEVEL
2=+Life 2=+Life
3= - Life 3= - Life
1=shield 1=shield
- -
-
BRIDGE SPEAKER
4 5 6 7 8
(4) GROUND LIFT-SELECTOR
(5) XLR INPUT SOCKETS
Connect the input signal here using a balanced XLR-plug.
(6) GAIN-CONTROLS
Adjust the desired volume here.
(7) TERMINAL BLOCK
For connecting the input signal and speakers.
(8) FILTER/BYPASS-SELECTOR
For activating a filter (see below).
(9) LOWPASS/HIPASS-SELECTOR
For switching between Lowpass and Hipass-filter (250 Hz).
(10) MONO BRIDGE-OUTPUT SELECTOR
For switching to bridged mode per channel-pair.
(11) AC VOLTAGE-SELECTOR
Make sure that the selector is properly set.
(12) FUSEHOLDER
Only replace the fuse when the device is disconnected from mains. Only use fuses of the same rating and
power.
(13) AC INPUT SOCKET
Used to plug the power cord in.

INSTALLATION

Please note: when using a PA-system in public or industrial areas, a series of safety instructions have to be
followed that this manual can only give in part. The operator must therefore inform himself on the current
safety instructions and consider them.

Rack installation

This amplifier is built for 19" racks (483 mm). The rack you use should be a Double-Door-Rack where you
can open the frontpanel and the rear panel. The rack should be provided with a cooling fan. When mounting
the amplifier into the rack, please make sure that there is enough space around the device so that the
heated air can be passed on. Steady overheating will damage your device.
You can fix the amplifier with four screws M6 in the rack.
Be careful when mounting the amplifier into the rack. Put the heaviest devices into the lower part of the rack.
Be aware that fastening the amplifier with four screws on the front panel is not enough. In order to ensure
safety, additional fastening by using ground and side bars is necessary.
If racks are to be transported or used for mobile use, additionally fasten the devices by connecting the rear
brackets with the side or ground bars of the rack. In this way, the amplifier cannot be pushed backwards.
The front panel alone is not designed to absorb acceleration forces occuring during transportation.
CH 7 CH 6 CH 5
BRIDGE
2 1 2 1
3 3
1=shield 1=shield
2=+Life 2=+Life
3= - Life 3= - Life
FILTER FILTER
BYPASS BYPASS
LOWPASS LOWPASS
HIPASS HIPASS
LEVEL LEVEL
2=+Life 2=+Life
3= - Life 3= - Life
1=shield 1=shield
- -
-
BRIDGE SPEAKER
9 10
CH 4 CH 3
BRIDGE
2 1 2 1 2 1
3 3 3
1=shield 1=shield
1=shield
2=+Life 2=+Life
2=+Life
3= - Life 3= - Life
3= - Life
FILTER FILTER FILTER
BYPASS BYPASS BYPASS
LOWPASS LOWPASS LOWPASS
HIPASS HIPASS HIPASS
LEVEL LEVEL LEVEL
2=+Life 2=+Life 2=+Life
3= - Life 3= - Life 3= - Life
1=shield 1=shield 1=shield
- - -
-
BRIDGE SPEAKER
23/29
CH 2 CH 1
Type : OMNITRONIC MCP-8150
Power supply : 115 V/230V AC, 50/60 Hz
Power consumption : 1850 W
BRIDGE Nominal Power Output : 8 x 150 W / 4 Ohms
Fuse : 10 A / 250 V - 20 A / 115 V
2 1
3
1=shield
2=+Life
OMNITRONIC SHOWEQUIPMENT GmbH, GERMANY
3= - Life
VOLTAG E SE L E C TOR
FILTER
BYPASS
1 1 5 V
LOWPASS
HIPASS
LEVEL
2=+Life
3= - Life
1=shield
-
-
BRIDGE SPEAKER
11 12 13
10452430_V_1_0.DOC
~
230V