Werbung
Swing the tail boom briskly to the right (i.e. the helicopter's
nose moves to the left).
With the tail rotor blades still folded together, the tip of the top
blade should now move towards the tail boom („Re" in the
drawing).
Reverse the gyro direction if necessary. If your gyro is a sim-
ple type without a reversing switch (e.g. G 200), invert the
gyro element.
Final checks
When all the servos are at neutral, the servo output arms
should be horizontal.
At this setting the pitch angle of the main rotor blades should
be +9°.
Maximum collective pitch should be around +14°, minimum
collective pitch around +4°.
Power system
Remove the main and tail rotor blades.
Run the motor in for the duration of one or two full battery
charges, varying the load (speed) constantly. The information
refers to the standard motor supplied with the model.
Adjusting blade tracking (fig.)
When you first operate the model you will need to check and
adjust blade tracking.
Carefully open the throttle until the blades are spinning, and
check the blade tracking from the side.
If the blades revolve at different heights when the rotor is at
hover speed, you need either to increase the pitch angle of
the lower blade B, or reduce the pitch angle of the higher
blade A.
This adjustment is made by locating the ball-link from the
mixer lever to the swashplate, and adjusting it by 1 or 2 turns
in the appropriate direction.
Maximum rotational speed of main rotor head with woo-
den blades: 1650 rpm.
General information on programming the radio control
system
The settings described in the following section assume the
use of a standard motor, the recommended Heli Control 825
speed controller and an FX 18 radio control system.
Assembly instructions
Eolo R 22
If your model helicopter is to operate efficiently the basic
mechanical adjustments must be correct.
For safety reasons remove the main and tail rotor blades
before making adjustments to the speed controller and thrott-
le programming.
Before you continue with programming the system the follo-
wing requirements must be fulfilled:
Adjust the speed controller as described in the operating
instructions.
The following values should be set In the swashplate mixer
(TAUM): ROLL = 100%, PITCH-AXIS = 100%, and PIT
(collective pitch) 40%.
The first step is to set the hover point.
Your aim should be to set up the helicopter so that it hovers
when the collective pitch stick is at centre, with a blade pitch
angle of +9°.
Set up the mixer swashplate travel in % terms so that the
collective pitch range is from +4° to +14°.
Diagram 1
Gas und Pitchkurve normal = Normal throttle and collective
pitch curve
Gas = Throttle
Pitch = Collective pitch
Steuerknüppelweg = Stick travel
Setting the throttle and collective pitch curve for Idle-Up
1 (GV-1)
Diagram 2
Gas und Pitchkurve 1 = Throttle and collective pitch curve 1
Gas = Throttle
Pitch = Collective pitch
Steuerknüppelweg = Stick travel
Tail rotor compensation (REVO)
Tail rotor compensation only needs to be set up if you are
using a gyro which requires this.
8
The aim is to eliminate any tendency for the helicopter to yaw
(swing to either side) when the model climbs or descends.
This unwanted rotation is caused by variations in the torque
generated by the rotor blades.
The basic requirement:
The model must first be trimmed neutrally for the hover, i.e.
when hovering the model should have no tendency to yaw.
Standard REVO value: 25%.
With the model at a steady hover, increase collective pitch
briskly.
If the model yaws in the opposite direction to the direction of
main rotor rotation, the value for tail rotor compensation
(REVO) must be increased.
If the model yaws in the same direction as the direction of
main rotor rotation, the value for tail rotor compensation
(REVO) must be reduced.
Important
After flying the model helicopter for the first time please take
the trouble to check that all screwed joints are still tight; this
applies in particular to the power train components and the
rotor system. All the following areas of the helicopter should
be re-greased or oiled at intervals of two or three hours:
Main rotor shaft in the swashplate area,
Tail rotor shaft in the area of the tail rotor slider,
Main gearbox, tail rotor gearbox.
And one final tip
On no account attempt to fly your new helicopter without enli-
sting the help of a good, experienced helicopter pilot. Many
apparently difficult problems sort themselves out virtually by
themselves if you can fall back on the experience of a com-
petent helicopter pilot.
robbe Modellsport GmbH & Co. KG
We reserve the right to alter technical specifications
Order No.
S 2865
Werbung
