Icons; Safety Guidelines For Battery Chargers; Original Accessories/Attachments; Before Use - Parkside PAKSP 20-Li A1 Originalbetriebsanleitung

■ Use only saw blades specified by the manufacturer which comply with
EN 847-1 (intended for cutting wood or similar materials).
■ Use only saw blades marked with a speed equal to or higher than the
speed indicated on the power tool.
Assembly and fastening of tools and tool parts
■ Tools and tool bodies must be clamped so that they cannot come loose
during operation.
■ When mounting the tools, you must ensure that the clamping is carried
out on the tool hub or the clamping surface of the tool and that the
cutting edges do not come into contact with each other or with the
clamping elements.
■ Mounting screws and nuts must be tightened using suitable spanners
etc. and to the torque specified by the manufacturer (9–12 Nm).
■ Extending the spanner or using hammer blows to tighten bolts is not
permitted.
■ All dirt, grease, oil or water must removed from the clamping surfaces.
■ Clamping screws must be tightened according to the manufacturer's
instructions.
■ To adjust the bore diameter of circular saw blades to the spindle diameter
of the machine, use only firmly inserted rings, e.g. rings that are pressed
in or affixed by adhesive bonding. The use of loose rings is not permitted.
Maintenance of tools
■ The maintenance of tools is not permitted. Danger due to imbalance!
Handling
Handle tools safely to avoid injury:
■ Wear personal protective equipment, especially protective gloves.
■ Make sure that you have secure footing.
■ Always wear closely fitting clothing.
■ After you have fitted the tool, re-attach all of machine's safety devices,
if any, correctly.
■ Have an expert carry out a test run.

Icons

Wear protective gloves!
Wear a dust mask!
Wear safety goggles!
Wear ear muffs!
Attention! Risk of injury!
Do not reach towards the running saw blade!
2
1
WARNING!
► The power tool creates an electromagnetic field during operation.
This field can, in certain circumstances, impair active or passive
medical implants.
To reduce the risk of serious or fatal injury, we recommend that
indi viduals with medical implants consult their physician and the
manufacturer of the medical implant before operating the power tool.
│ GB │ CY
■ 6
1. Set the adjustable fence
2. Set the bevel angle.

Safety guidelines for battery chargers

This appliance may be used by children aged 8 years
■
and above and by persons with limited physical,
sensory or mental capabilities or lack of experience
and knowledge, provided that they are under super-
vision or have been told how to use the appliance
safely and are aware of the potential risks. Do not
allow children to use the appliance as a toy. Cleaning
and user maintenance tasks may not be carried out
by children unless they are supervised.
To avoid potential risks, if the mains cable of this
■
appliance is damaged, it must be replaced by the
manufacturer, its customer service department or a
similarly qualified person.
The charger is suitable for indoor use only.
ATTENTION!
♦ This charger can only charge the following batteries:
PAP 20 A1/PAP 20 A2/PAP 20 A3.
♦ A current list of battery compatibility can be found at
www.Lidl.de/Akku.
WARNING!
■ Do not operate the appliance with a damaged cable, power cord or
mains plug. Damaged power cords can result in danger to life due to
electric shock.

Original accessories/attachments

Use only the accessories and additional equipment that are specified in
the operating instructions and are compatible with the appliance.
WARNING!
■ Do not use any accessories that are not recommended by PARKSIDE.
This can lead to an electric shock and fire.

Before use

Charging the battery pack

CAUTION!
► Always unplug the appliance before you remove the battery pack
from or connect the battery pack to the battery charger .
NOTE
.
► Never charge the battery pack if the ambient temperature is below
10°C or above 40°C. If a lithium-ion battery is to be stored for an
extended period, the charge level should be checked regularly. The
optimum charge level is between 50% and 80%. The storage climate
should be cool and dry, and the ambient temperature should be
between 0°C and 50°C.
♦ Insert the battery pack
♦ Insert the power plug into the socket. The red control LED
♦ The green control LED
and the battery pack
♦ Always unplug the appliance before you remove the battery pack
from the battery charger .
into the battery charger .
indicates that the charging process is complete
is ready for use.
PAKSP 20-Li A1
lights up.