Before Starting The Equipment; Operation - EINHELL HTO 2000 Originalbetriebsanleitung

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Assembly (fi g. 1/2)
•
Join the two halves of the base (5a/5b)
together by inserting the pins (A) into the
location holes (B).
•
Use the supplied screws (C) to fasten the
base (5) to the heater housing (D).
•
Guide the power cable through the cable
guides and the recess (9) to the outside.
5.2 Remote control
Note: All modes and functions can be set using
the buttons on the appliance as well as with the
remote control. The remote control requires a CR
2032 button cell (included in the remote control).
Pull the contact protection (small plastic plates)
out of the housing before use.
•
Never use a battery type other than the speci-
fied one.
•
If the remote control is not used for a lengthy
period of time, remove the battery to prevent
it leaking.
•
Point the remote control towards the heater.
The range is max. 5 meters.
•
Direct sunlight and objects can considerably
reduce the range of the remote control.
•
Handle the remote control with care. Do not
drop it and keep it away from heat and mois-
ture.
Inserting the battery (Fig. 3):
1. Open the battery compartment cover by
pressing the lock (D) towards the middle and
pulling the battery compartment out at the
same time.
2. Make sure you fi t the battery with the + and
– terminals correctly positioned as shown on
the housing.
3. Press the battery compartment cover into the
remote control.
As the end user you are legally required to return
spent batteries. You can hand them in at public
collection points provided by your council or sales
outlets where batteries of this type are sold. Ob-
Anl_HTO_2000_SPK9.indb 17 Anl_HTO_2000_SPK9.indb 17
GB
serve the instructions in section 11 as well.
The equipment can be used indoors in a free
standing position. Keep a minimum distance of 1
m between the housing and walls, combustible
materials (furniture, curtains, etc.). The equipment
may only be used completely mounted and stan-
ding vertically on a stable surface. It is prohibited
to operate the equipment on an instable surface
(e.g. on a bed).
Read the safety regulations in section 1.
Check the correct air throughput by holding a
sheet of paper a distance of 10 cm in front of the
air outlet grille. The paper must be blown away
from the air outlet grille.
When the equipment is used for the fi rst time or
after a long period of rest it may emit an odor for a
short time. This is not a fault.

6. Operation

Note: The measured room temperature appears
in the LED display when the equipment is
switched on.
6.1 Switching the mains voltage on/off (Fig.
1)
The main switch (8) disconnects the equipment
completely from the mains power supply. The
fi rst step when you want to use the equipment
is to turn on ("I") the main switch; the last step
when you no longer need the equipment is to turn
off ("0") the main switch. When you turn on the
main switch, an acoustic signal sounds by way of
confi rmation and the status panel (fi g. 5/E) lights
up.
6.2 Switching the equipment on and off /
adjusting the desired temperature (Fig.
4a/4b/5)
Press the "ON/OFF" button (F). The "H" LED and
"HI" in the display will fl ash (light up) for maximum
heat output. The room temperature measured
on the heater will then appear in the display. If
the set desired temperature is higher than the
room temperature measured on the equipment,
the equipment starts heating. If the set desired
temperature is lower than the measured room
temperature, the "H" LED will continue fl ashing
and the equipment will not heat. Press the "+"
button (L) to increase the desired temperature.
- 17 -
24.01.2019 13:30:09 24.01.2019 13:30:09