Proper Use; Technical Data; Before Starting The Equipment; Operation - EINHELL IHS 1500 W Originalbetriebsanleitung

3. Proper use

The equipment can be used indoors or outdoors
in a weather-protected area (not in the rain). The
equipment is not suitable for heating baby chan-
ging tables or for drying towels and textiles.
Do not cover the equipment – risk of fi re! The hea-
ter warms objects or persons at which it is pointed
but does not directly heat the air in the process.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Mains voltage: ........................ 220-240 V ~ 50 Hz
Max. heat rating ...................................... 1500 W
Protection type: ............................................ IP55

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Mounting on a wall
Warning!
•
Keep a minimum distance of 200 cm between
the front grille and any objects (e.g. curtains),
walls and other structural elements. There
must be a clearance of 50 cm between the
side of the equipment and any objects or
walls which are not within the radius of radi-
ation. The distance to the ceiling must be at
least 50 cm.
•
Mounting in a horizontal and stationary posi-
tion on vertical walls at a height of at least 1.8
m above the floor is mandatory. The distance
to the ceiling must be at least 50 cm.
Anl_IHS_1500_W_SPK7.indb 15 Anl_IHS_1500_W_SPK7.indb 15
GB
•
The equipment is not allowed to be fitted to
the ceiling. The heat emitted by the heater
may turn wooden ceilings dark in spite of ob-
serving the minimum distance to the ceiling.
Caution! Make sure that there are no electric
cables or other installations (for example water
pipes) near the drill holes. Ensure that the equip-
ment is secured fi rmly and horizontally to the wall.
Use only suitable fastening material on a wall
capable of bearing the load. The supplied dowels
and screws are suitable for the following: Con-
crete, natural stone with a dense structure, solid
brick, solid limestone bricks, solid lightweight
concrete bricks and aerated concrete.
•
To mount on a wall, please use the supplied
wall bracket.
•
Fig. 2: The screws (E) are already pre-fitted
according to the model. If this is not the case,
lock the holding arm (D) and the sleeve (C)
each with one screw M 3x6 mm (E).
•
Fig. 2: Transfer the position of the four drill
holes (Ø 8 mm) from the wall plate (B) onto
the wall with a marker. Remember to allow for
the minimum clearances specified above.
•
Drill the holes in the wall and insert the do-
wels.
•
Screw the wall bracket tightly in place.
•
Fig. 4: Place the heater head on the wall bra-
cket and secure it to the wall bracket with the
securing screw M 6x10 mm (fig. 3).

6. Operation

Important. Before using the equipment for the fi rst
time, check that the voltage supply is the same
as the voltage details set out on the rating plate.
Read the safety regulations in section 1.
When the equipment is used for the fi rst time or
after a long period of rest, it may emit an odor for
a short time. This is not a fault.
If black spots appear on the heating elements du-
ring the fi rst minutes of operation, this will aff ect
neither the quality nor performance of the heater.
6.1 Switching on the equipment (Fig. 4/5)
•
To switch on the main switch, pull once on the
pull-switch cord (M). The LED (K) will light up.
•
To switch on the heater, press the button (F)
once.
- 15 -
22.02.16 09:55 22.02.16 09:55