Technical Data - EINHELL BG-RS 2845 CB Originalbetriebsanleitung

Anleitung_BG_RS_2845_CB_SPK7:_

2. Technical data

Voltage:
Power rating:
Protection type
Cutting unit idling speed
Branch diameter:
L sound pressure level:
pA
L sound power level:
WA
Weight:
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
5. Before starting the equipment
1. Screw the motor unit (Fig. 4/Item 1) and the base
frame (Fig. 4/Item 3) together. Use the screws
(Fig. 3/Item 12) and washers (Fig. 3/Item 13) to
do so.
2. Fit the wheels to the base frame. To do so, slide
one sleeve each into the hole in each of the
wheels (Fig. 6). Then insert one screw with
washer through each sleeve (Fig. 7) and screw
the wheels to the base frame (Fig. 8). To do so,
fit one washer in front of the tubular rod and one
behind it. Press the wheel caps onto the wheels
(Fig. 9).
3. Fit the legs (Fig. 10/Item 11) to the base frame
as shown in Fig. 10.
4. Slide the shredded material debris box into the
mount with the safety switch (Fig. 12/Item A) at
the front as shown in Fig. 11. Ensure that the
shredded material debris box runs above the
23.11.2009 15:52 Uhr
guide rails (Fig. 4/Item A).
5. Lock the shredded material debris box with
safety switch (Fig. 12/Item A) in position by
230-240 V ~ 50 Hz
pushing upwards.
2800 W (S6-40%)
2300 W (S1)
6. Operation
IP24
40 min -1
Please observe the statutory regulations governing
noise abatement during operating times, which may
max. 45 mm
differ from town to town.
72 dB (A)
92 dB (A)
6.1 Mains connection
Connect the device with an extension lead
31,7 kg
connected to the integrated power plug (Fig. 13/Item
E). Be sure to observe the relevant information in the
safety instructions.
6.2 ON/OFF switch (Fig. 13/Item B)
Press the green knob to switch on the shredder.
Press the red knob to switch it off.
Note: The device has a zero voltage switch. This
prevents the device restarting unintentionally after a
power failure.
6.3 Safety switch (Fig. 12/Item A)
When using the device the shredded material debris
box must be securely in position and the safety
switch locked as shown in Fig. 12.
6.4 Direction selection switch (Fig.13/Item C)
Important! The switch for selecting the direction
of rotation can only be moved when the shredder
is switched off.
Position "⇓"
The material is automatically drawn in by the blade
and shredded.
Position "⇑"
The blade rotates in the opposite direction to release
jammed material. After moving the selector switch to
the "⇑" position, press and hold the green knob of the
ON/OFF switch. The blade will start to rotate in the
opposite direction. As soon as you release the
ON/OFF switch, the shredder will stop automatically.
Important! Always wait until the shredder has
reached a standstill before you switch it on
again.
Note: If the switch for selecting the direction of
rotation is in its center position, the motor will not
start.
Seite 13
GB
13