Proper Use; Technical Data; Operation - EINHELL 34.305.90 Originalbetriebsanleitung

Anleitung_BG_RS_2540_1_CB_SPK1__ 05.02.15 09:33 Seite 14
GB

3. Proper use

This electric garden refuse shredder is designed only
for shredding organic garden waste. Place biologi-
cally degradable material, e.g. leaves, branches,
dead flowers etc., into the loading funnel inlet.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Voltage:
Power rating:
Cutting unit idling speed
Branch diameter:
L sound pressure level:
pA
K uncertainty
L sound power level:
WA
Weight:
Protection class:
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
14
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
2. Damage to hearing if no suitable ear protection is
3. Health damage caused by hand-arm vibrations if
5. Before starting the equipment
1. Screw the motor unit (Fig. 4/Item 1) and the base
2. Fit the wheels to the base frame. To do so, slide
230-240 V ~ 50 Hz
2500 W (S6-40%)
2000 W (S1)
40 min -1
max. 40 mm
3. Fit the legs (Fig. 10/Item 11) to the base frame
80.9 dB (A)
3 dB (A)
4. Slide the shredded material debris box into the
94 dB (A)
30 kg
I
5. Lock the shredded material debris box with

6. Operation

Please observe the statutory regulations governing
noise abatement during operating times, which may
differ from town to town.
6.1 Mains connection
Connect the device with an extension lead
connected to the integrated power plug (Fig. 13/Item
E). Be sure to observe the relevant information in the
safety instructions.
is used.
used.
the equipment is used over a prolonged period or
is not properly guided and maintained.
frame (Fig. 4/Item 3) together. Use the screws
(Fig. 3/Item 12) and washers (Fig. 5/Item 13) to
do so.
one sleeve each into the hole in each of the
wheels (Fig. 6). Then insert one screw with
washer through each sleeve (Fig. 7) and screw
the wheels to the base frame (Fig. 8). To do so,
fit one washer in front of the tubular rod and one
behind it. Press the wheel caps onto the wheels
(Fig. 9).
as shown in Fig. 10.
mount with the safety switch (Fig. 12/Item A) at
the front as shown in Fig. 11. Ensure that the
shredded material debris box runs above the
guide rails (Fig. 4/Item A).
safety switch (Fig. 12/Item A) in position by
pushing upwards.