Battery Charging - Comet CPS 50 Handbuch

2 Suction motor switch
2A Suction motor operation led
3 Battery power test
3A Green led - full battery charge
3B Yellow led - 50% battery charge
3C Red led - battery discharged
PHOTO D MODEL B - (DC 24V)
1 General on / off key switch
2 Brush operation lever
3 Brush plate lift/lower lever
4 Squeegee lift/lower lever
5 Brush motor thermal breaker
6 Recovery tank drain hose
7 Battery connector
8 Water outlet adjusting lever
PHOTO E MODEL BT/T - (DC 24V
WITH TRACTION)
1 Battery power test
1A Green led - full battery charge
1B Yellow led - 50% battery charge
1C Red led - battery discharged
2 Forward/reverse indicator
3 Reduce speed switch
3A Traction speed 1
3B Traction speed 2
3C Traction speed3
3D Traction speed 4
4 Increase speed switch
5 Brush motor switch
5A Brush motor operation led
6 Suction motor switch
6A Suction motor operation led
PHOTO F MODEL BT/T - (DC 24V
WITH TRACTION)
1 General on / off key switch
2 Forward/reverse traction operation lever
3 Brush plate lift/lower lever
4 Squeegee lift/lower lever
5 Brush motor thermal breaker
6 Traction motor thermal breaker
7 Recovery tank drain hose
8 Battery connector
9 Water outlet adjusting lever
PHOTO G MODEL B - BT/T - (DC 24V
WITHOUT AND WITH TRACTION)
1 Battery compartment opening lever
2 Solution tank filling opening
PHOTO H MODEL B - BT/T - (DC 24V
without and with traction)
Battery connection diagram
PHOTO I MODEL B - BT/T - (DC 24V
without and with traction)
1 Opening clip spring
2 Battery compartment with 12v
Batteries
3 Battery connection wiring
PHOTO L
without and with traction)
1 Built-on battery charger
2 Battery charger power supply cable
PHOTO M
1 Squeegee bumper wheel
2 Squeegee pression adjusting knob
3 Suction hose
4 Squeegee blades replacement
knob
5 Squeegee wheel
6 Squeegee fixing knob
7 Squeegee inclination adjusting
knob
PHOTO N
1 Hood of suction filter compartment
2 Solution tank filling opening
3 Recovery tank
4 Solution tank
PHOTO O
1 Floating device
2 Suction filter
3 Recovery tank inspection
PHOTO P
1 Solution water filter
6.3

BATTERY CHARGING

Connect the patch cord to the power cable of the
battery charger ( Photo L - 2 ) and to the mains
power.
On switching on the battery charger will check the
battery voltage and decide whether to start the
charging process. If the battery is not connected
to the battery charger, the red LED will flash. If the
result of the test is positive after 1 second the char-
ging of the battery can start, with the red LED on.
The progress of the charging process is shown by
three LED's: red, yellow and green, as in the whole
range of the battery chargers.
The green LED shows the end of the charging or
the last phase in case of deep charging process; in
the former case, the relay is opened to disconnect
galvanically the battery from the battery charger.
• For further information refer to the use and sa-
fety manual of the battery charger provided by the
manufacturer.
If the machine is equipped with Pb-Acid batteries,
charge only in a well-ventilated area, lift the supe-
rior cover and open the battery plugs.
• Follow the steps indicated in the battery ma-
nufacturer's operating and safety manual (see the
battery maintenance section).
33
MODEL B - BT/T - (DC 24V
MODEL E - B - BT/T
MODEL E - B - BT/T
MODEL E - B - BT/T
MODEL E - B - BT/T