Cleaning And Disinfection; Storage And Transportation - 3M 6000 serie Handbuch

valve is fully engaged under all three lugs on post,
lies flat, and spins freely on post.
Head Harness (6897) Replacement.
Unbuckle head harness straps and replace with
new head harness. Figure 11.
Lens Assembly (6898) Replacement.
Remove the two sets of screws using a screwdriver.
Then, pull the frame top and frame bottom away
d
from the faceseal. The frame top, frame bottom,
faceseal and the lens assembly have vertical line
e
markings that indicate their positions relative to one
another. Make certain these markings are aligned
e
for re-assembly. Figure 12.
Neck Strap (7883).
Connect loops at end of neck strap assembly onto
t
the face seal tabs at the top of the head harness.
re
ACCESSORIES
y,
Spectacle Kit (6878).
Install rail assembly into Facepiece with the plastic
t. foot positioned on centre port adapter and the top of
rail centred between the lugs or projections at top of
face seal. Install frame assembly onto rail assembly
by inserting pins into holes in rubber slide.
m Spectacles can now be adjusted for optimal fit and
m vision.
Lens Covers (6885).
Remove release liner from adhesive at each side of
replacement lens cover. Position lens cover over
e
the facepiece lens and adhere in place. Remove
used lens cover by lifting tab away from facepiece.

CLEANING AND DISINFECTION

Cleaning is recommended after each use. If the
respirator is to be used for more than one shift it
should be cleaned at the end of each shift and
stored in the original packaging or a sealed
container. Use the 3M™ 105 Face Seal Cleaner to
ed
clean the respirator. Remove the filters and
disconnect the air supply unit if appropriate. Clean
parts (excluding filters) by immersing in warm
et
cleaning solution (water temperature not to exceed
50°C), scrub with soft brush until clean. Add neutral
detergent if necessary. Disinfect respirator by
e
soaking in a solution of quaternary ammonia
se
disinfectant or sodium hypochlorite or other
disinfectant. Rinse in clean, warm water and air dry
d
at room temperature in a non-contaminated
ve
atmosphere.
t
n
n
CAUTION Do not use cleaners containing lanolin or
other oils on these products. Do not autoclave. Do
not use petrol, chlorinated degreasing fluids (such
as trichloroethylene), organic solvents or abrasive
cleaning agents to clean any part of the equipment.
Do not reassemble parts until facepiece is
completely dry.
STORAGE AND
TRANSPORTATION
These products should be stored in the packaging
provided in dry, clean conditions away from direct
sunlight, sources of high temperature, petrol and
solvent vapours. The original packaging is suitable
for transporting the product throughout the
European Union. When stored as stated, the
expected shelf life of the product is 5 years from
date of manufacture. Store in accordance with
manufacturer's instructions, see packaging.
End of Shelf Life
]
Temperature Range
\
Maximum Relative Humidity
,
Name and address of Legal Manufacturer
:
Dispose in accordance with local regulations
J
Packaging not suitable for food contact.
The date of manufacture can be established by
examining the date clock on the inside of the
facepiece. Figure 13. The inner segment will display
the year, and the arrow will point to the month of
manufacture in the outer segment. The example
shows 01/09/2011 - 30/09/2011.
APPROVALS
These products are type approved and audited
annually by either: BSI Group The Netherlands B.V.
John M. Keynesplein 9, 1066 EP Amsterdam, The
Netherlands, Notified Body No. 2797. and / or BSI
Assurance UK Ltd, Kitemark Court, Davy Avenue,
Knowlhill, Milton Keynes MK5 8PP, UK, Notified
Body No. 0086. These products meet the
requirements of European Regulation (EU)
2016/425 and applicable local legislation. The
applicable European/local legislation and Notified
Body can be determined by reviewing the
Certificate(s) and Declaration(s) of Conformity at
www.3m.com/Respiratory/certs.
8
TE
Re
wit
EN
*A
HS
Ple
wo
the
Ple
Ey
(In
Sp
lat
Flo
Ma
l/m
Ma
Ma
CA
eq
mo