Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
Installation instructions for sectional doors type
iso9-2
/
iso20-2
disassembled version
The door manufacturer accepts no liability for incorrect
mounting.
- Mounting should only be carried out by qualified fitters
Please read carefully before mounting
Scope of delivery:
Section package, frame package, panel package
The following items are required for mounting
•
the following tools (place inside the garage before
mounting the door if there is no other entrance to the
garage)
folding rule/tape measure, water level, water pump pliers,
reversible ratchet handle with extension and wrench socket
inserts size 7, 10 and 13 ( fork or wrench socket also
possible) fork or open spanner from size 13 for tightening
springs (cf. Item 29), cross-tip screwdrivers size 2 and 3,
slot screwdriver, hammer drill with drill bits, ∅10mm
(drilling depth of at least 65mm), at least 2 screw clamps,
possibly square timber, hammer, metalsaw, small nippers,
chisel and
• • • •
Mounting material suitable for the building situation. Note:
Check that the wood screws S8 supplied and the plugs
S9 are suitable for the building situation before use.
• • • •
Important :
• • • •
The door may only be mounted in a finished opening
and on a finished floor!
•
As a precautionary measure, compare the garage
dimensions with the coordinating size of the door before
mounting.
−
minimum inside width of garage
= coordinating size –width + 180mm
−
minimum garage ceiling height
=coordinating size –height + 120mm (also suffices for
door operators)
−
minimum side room right and left = 55mm
•
Letter/numeral combinations, e. g. S8, refer to the
respective mounting and installation materials in the
illustrated section, a successive subscript L or R, e.
g. 1
, indicates a part for the left or right side (observe
L
markings on parts). The omission of a subscript L or R
indicates a part that can be used either left or right.
Figures in brackets, e. g. [
illustration
in
The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!
with
extension
spring,
], refer to the respective
1.10
the
illustrated
section.
Mounting of door frame
( 1 )
Lay the angular frames 1
similar (to protect them from scratches) and screw together
the angular frame 1
(tapping screws have already been pre-mounted) [
( 2 )
Screw the leading plate 4 with S13 on top on the angular
frames 1
+ 1
[
1.10b
R
L
( 3 )
Loosely screw the wall anchor 7 to the angular frames
1
right and left with S6 + M12 according to the side
R/L
room.
( 3a ) Side room 55 - 120mm: Set the wall anchor 7 to the
[
inside
1.10ca
( 3b ) Side room more than 120mm: set the wall anchor 7
[
to the side
If other mounting materials are used, make sure they
have at least the same load-carrying capacity as the
supplied wall anchor 7.
( 4 )
Set up the door frame behind the opening, secure it so it
cannot fall over, and use the water level to align exactly
parallel and at a right-angle [
frame panel 3 is level). Centre and clip panel retainers 13
to the upper frame part [
[
]. Put the srew S8 in the plastic bush 81 and fix
1.15a,c,d,e
the foot of the frame
angular frames 1
space between frame and masonry with suitable
material before tightening the screws!!!
( 5 )
Screw each of the right 14
tracks to end piece 16
[
] + spring channel bracket 8 each front & back
1.20a
[
]+ end connection bracket 10
1.20b,c
S12.
( 6 )
Stick on foamed rubber 9 on spring channel bracket 8
[
], mount spring channel 12 with S6 + S12 and put on
1.20b
the edge protection 24 on the front [
( 7 )
Mounting of anchor tracks
( 7a ) If the distance between the wall and the pair of
horizontal tracks 14
(internal width of the garage max. coordinating size+
1030mm if door is fitted in the middle) push an
anchor track 27 with connecting brackets 28 right
and left into the track connector 6 and screw the
clamping plate 29 to S6 + S12 in such a way that the
anchor tracks can still be pulled out
( 7b ) If the distance between the wall and the pair of
horizontal tracks is more than 500mm the track
connector 6 can be later fixed to the ceiling (Cf .
Point. 14).
( 8 )
Screw the horizontal pair of tracks 14
16
with the header bracket S5 + S12 so that later the
R/L
door remains raised when lifted up [
the wall to small than use the hammer head screw S7
.
[
]
1.25c
( 9 )
Screw the track connector 6 each with S6 + S12 to the end
connection brackets 10
( 10 ) Premount springs [
Place both triple extension spring assemblies 11 with the
plastic sliding elements downwards on the floor of the
garage (with the spring tightening strap pointing to the back
wall of the garage). Screw a deflection pulley cable
assembly 12 with the black side showing upwards to one
of the triple extension spring assemblies 11 with S5 + S12.
This is the right spring assembly. Both cable ends are
- 1 -
+ 1
on to wood or something
R
L
+ frame panel 3 + angular frame 1
R
].
]
.
]
.
1.10cb
] (also ensure that the
1.15
]. Finally fasten with S8 + S9
1.15d
. Note: do not twist or bend the
[
]
1.15b
; it might be necessary to fill the
R/L
and left 14
pair of horizontal
R
L
[
] + upper rope fixation 5
1.20a
R/L
[
1.20d
R/L
].
1.20e,f
is smaller than 500mm
R/L
[
1.20a,b
to the end pieces
R/L
]. If the distance to
1.25c
[
].
1.25d
R/L
].
1.30
L
].
1.10a
] with S6 +
]
.
Werbung
