Werbung
Verfügbare Sprachen
Verfügbare Sprachen
- The electrical installation must include a
double
pole
clearance of at least 3 mm, correctly sized
and in accordance with the electrical
standards of the country of installation
- Please follow the connections diagram for
the electrical connections.
- If an earth connection is necessary, check
that
adequate
it
correctly
thermal
protection
adequate
has
thermal
protection
adjusted to the corresponding limits.
has
- If a ventilator is installed in a duct, the duct
adjusted to the corresponding limits.
must be exclusively for the ventilation
- If a ventilator is installed in a duct, the duct
must be exclusively for the ventilation
system.
system.
Starting up.
Before starting up the machine, make sure
Starting up.
that:
Before starting up the machine, make sure
- The apparatus is well secured and the
that:
electrical connections have been carried
- The apparatus is well secured and the
electrical connections have been carried
out correctly.
- The safety devices have been adequately
out correctly.
- The safety devices have been adequately
connected.
- No loose material or fitting remains can be
connected.
- No loose material or fitting remains can be
sucked up by the ventilator. If the ventilator
has been mounted in a duct, make sure it
sucked up by the ventilator. If the ventilator
is clear of loose material.
has been mounted in a duct, make sure it
- The
earth
fittings
is clear of loose material.
- The
connected.
earth
fittings
- The electrical safety devices are correctly
connected.
- The electrical safety devices are correctly
connected, adequately adjusted and ready
connected, adequately adjusted and ready
for use.
- The wire and electrical connections inputs
for use.
are correctly sealed and water-tight.
- The wire and electrical connections inputs
are correctly sealed and water-tight.
When starting up the machine, make sure
When starting up the machine, make sure
that:
that:
- The propeller turns in the correct direction.
- There are no abnormal vibrations.
- The propeller turns in the correct direction.
- There are no abnormal vibrations.
- If any of the electrical safety devices blow,
the
apparatus
- If any of the electrical safety devices blow,
disconnected from the mains supply. The
the
apparatus
whole installation should be carefully
disconnected from the mains supply. The
whole installation should be carefully
checked before trying to start up the
checked before trying to start up the
machine again.
machine again.
Maintenance.
- Before manipulating the ventilator, make
Maintenance.
sure it is disconnected from the mains
- Before manipulating the ventilator, make
sure it is disconnected from the mains
supply even if it has previously been
switched off. Prevent the possibility of
supply even if it has previously been
anyone else connecting it while it is being
switched off. Prevent the possibility of
anyone else connecting it while it is being
manipulated.
- The
apparatus
manipulated.
inspected. These inspections should be
- The
apparatus
carried out bearing in mind the machine's
inspected. These inspections should be
carried out bearing in mind the machine's
working conditions, in order to avoid dirt or
working conditions, in order to avoid dirt or
dust accumulating on the propeller, turbine,
dust accumulating on the propeller, turbine,
motor or grids. This could be dangerous
motor or grids. This could be dangerous
switch
with
a
connected
and
overloading
and
been
and
connected
overloading
been
connected
are
adequately
are
adequately
must
be
must
be
must
be
must
be
anyone else connecting it while it is being
manipulated.
contact
- The
inspected. These inspections should be
carried out bearing in mind the machine's
working conditions, in order to avoid dirt or
dust accumulating on the propeller, turbine,
motor or grids. This could be dangerous
that
and perceptibly shorten the working life of
and
the ventilator unit.
and perceptibly shorten the working life of
and
- While cleaning, great care should be taken
the ventilator unit.
not to unstable the propeller or turbine.
- While cleaning, great care should be taken
- All maintenance and repair work should be
not to unstable the propeller or turbine.
- All maintenance and repair work should be
carried out in strict compliance with each
country's current safety regulations.
carried out in strict compliance with each
country's current safety regulations.
Recycling.
- EEC
Recycling.
responsibility we should assume with
- EEC
future generations in mind, oblige us to
responsibility we should assume with
future generations in mind, oblige us to
recycle all the materials we can. Therefore,
recycle all the materials we can. Therefore,
please deposit all left-over material and
please deposit all left-over material and
packaging in their corresponding recycling
packaging in their corresponding recycling
containers and hand in the replaced
containers and hand in the replaced
machines to the nearest handler of this
type of waste product.
machines to the nearest handler of this
type of waste product.
If you have any queries about S&P products,
If you have any queries about S&P products,
please contact our after-sales service in
Spain, or your local S&P dealer in any other
please contact our after-sales service in
country. If in doubt, please visit our Web -
Spain, or your local S&P dealer in any other
Page at
country. If in doubt, please visit our Web -
Page at
quickly
quickly
regularly
regularly
apparatus
must
Standards,
together
Standards,
together
www.solerpalau.com
www.solerpalau.com
be
regularly
with
the
with
the
Werbung
