S&P TD-SILENT serie Anweisungshandbuch Seite 57

ENGLISH
Thank you for placing your confidence in S&P by buying this
product. It has been manufactured following current technical
safety regulations and in compliance with EC standard.
Please read this instructions booklet carefully before installing
or starting up the product. It contains important information on
personal and user safety measures to be followed while
installing, using and carrying out maintenance work on the
equipment. Once the product has been installed, please hand
in this booklet to the end user.
Check that the apparatus is in perfect condition while
unpacking. Any fault or damage caused in origin is covered by
the S&P guarantee. Please make sure that the apparatus
coincides with the product you have ordered and that the
details on the instructions plate fulfil your necessities.
Transport and manipulation.
The packaging used for this apparatus has been designed
-
to support normal transporting conditions. The apparatus
must always be transported in its original packaging as not
doing so could deform or damage the product.
The product should be stored in a dry place in its original
-
packaging, protected from dust and dirt until it is installed
in its final location. Do not accept delivery if the apparatus
is not in its original packaging or shows clear signs of
having been manipulated in any way.
Do not place heavy weights on the packed product and
-
avoid knocking or dropping it.
Important information for the safety of installers and users.
Installation must only be carried out by qualified persons.
-
Make sure that the installation complies with each
-
country's current mechanical and electrical norms.
Once ready to use, the apparatus must fulfil the following
-
standards:
 Standard for Low Pressure Instalments
2006/95/CE
 Standard for Electromagnetic Compatibility
2004/108/CE.
Ventilators, or apparatus that include them, have been
-
designed to move the air in the area stipulated on their
characteristics plate.
This apparatus must not be used in explosive or corrosive
-
atmospheres.
If a ventilator is going to be installed to extract air from
-
premises where a boiler or other combustion apparatus
are installed, make sure that the building has sufficient air
intakes to assure adequate combustion. The extractor
outlet must not be connected to a duct used to exhaust
smoke or fumes from any appliance that uses gas or any
other type of fuel.
This appliance can be used by children aged from 8 years
-
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been
concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Safety during installation.
Make sure there are no loose elements near the ventilator,
-
as they could run the risk of being sucked up by it. If it is
going to be installed in a duct, check that it is clean of any
element that could be sucked up by the ventilator.
When installing an apparatus, make sure that all the
-
fittings are in place and that the structure which supports it
is resistant enough to bear its weight at full functioning
power.
Before manipulating the apparatus, make sure the mains
-
supply is disconnected, even if the machine is switched
off.
given supervision or
Check that the mains supply voltage and frequency values
-
coincide with the stipulations on the characteristics plate.
The electrical installation must include a double pole
-
switch with a contact clearance of at least 3 mm, correctly
sized and in accordance with the electrical standards of
the country of installation
Please follow the connections diagram for the electrical
-
connections.
If an earth connection is necessary, check that it correctly
-
connected and that adequate thermal and overloading
protection has been connected and adjusted to the
corresponding limits.
If a ventilator is installed in a duct, the duct must be
-
exclusively for the ventilation system.
Starting up.
Before starting up the machine, make sure that:
The apparatus is well secured and the electrical
-
connections have been carried out correctly.
The safety devices have been adequately connected.
-
No loose material or fitting remains can be sucked up by
-
the ventilator. If the ventilator has been mounted in a duct,
make sure it is clear of loose material.
The earth fittings are adequately connected.
-
The electrical safety devices are correctly connected,
-
adequately adjusted and ready for use.
The wire and electrical connections inputs are correctly
-
sealed and water-tight.
When starting up the machine, make sure that:
The propeller turns in the correct direction.
-
There are no abnormal vibrations.
-
If any of the electrical safety devices blow, the apparatus
-
must be quickly disconnected from the mains supply. The
whole installation should be carefully checked before
trying to start up the machine again.
Maintenance.
Before manipulating the ventilator, make sure it is
-
disconnected from the mains supply even if it has
previously been switched off. Prevent the possibility of
anyone else connecting it while it is being manipulated.
The apparatus must be regularly inspected. These
-
inspections should be carried out bearing in mind the
machine's working conditions, in order to avoid dirt or dust
accumulating on the propeller, turbine, motor or grids. This
could be dangerous and perceptibly shorten the working
life of the ventilator unit.
While cleaning, great care should be taken not to unstable
-
the propeller or turbine.
All maintenance and repair work should be carried out in
-
strict compliance with each country's current safety
regulations.
Recycling.
instruction
EEC Standards, together with the responsibility we should
-
assume with future generations in mind, oblige us to
recycle all the materials we can. Therefore, please deposit
all left-over material and packaging in their corresponding
recycling containers and hand in the replaced machines to
the nearest handler of this type of waste product.
If you have any queries about S&P products, please contact
our after-sales service in Spain, or your local S&P dealer in
any other country. If in doubt, please visit our Web-Page at
www.solerpalau.com.