Maintenance - Chicco Enjoy Fun Gebrauchsanweisung

dry the metal parts to prevent the formation of rust if the stroller
has come into contact with water.

MAInTEnAnCE

Lubricate the moving parts only if necessary, with a light application
of a silicone based lubricant. Regularly check the condition of the
wheels and, keep them clean of dust and sand. To avoid friction that
may prevent the correct operation of the stroller, ensure that all
the movable plastic parts placed along the metal frame are clean
of dust, dirt or sand. Keep the stroller in a dry place.
GEnERAL InSTRUCTIonS
HoW To oPEn THE STRoLLER
WARNING: When opening the stroller, ensure that your child, or
other children, are at a safe distance. Ensure that during these
operations the movable parts of the stroller do not come into
contact with your child.
1. Pull the trigger opening mechanisms, located on the handles of the
stroller, at the same time; the stroller will start to open (diag. 1).
2. Lift the stroller towards you to make the opening operation
easier (diag. 2).
3. Press the rear locking mechanism in a downward direction with
the tip of your foot to open the stroller fully, and lock it in the
open position (diag. 3).
WARNING: Ensure that the stroller is locked in the open position, by
checking that the rear locking mechanism is effectively secured.
HoW To ASSEMBLE THE BACKREST
CoMPonEnTS
A. Backrest adjustment rack
B. Backrest adjustment lever
C. Front joint
D. Front joint locking housing
E. Release button
F. Rear joint
G. Locking pin
4. To fit the backrest, first fix the rear joint (F), turning it until the
two locking pins located on the frame coincide with the holes
located on the joint (diag. 4).
5. After inserting the locking pins into the holes, push the joint,
until a click is heard, indicating that the locking pins are correctly
locked into position (G), as shown in diagram 5.
Repeat operations 4 and 5 on the other side of the backrest.
6. Fix the front joint (C), pushing it into its appropriate housing
(D), exercising a slight pressure on the tube of the backrest, as
shown in diagram 6, until a click is heard, indicating that it is
correctly locked into position. Repeat the operation on the other
side of the backrest.
7. WARNING: Ensure that, after carrying out the assembly
operations, the adjustment levers of the backrest (B) are located
under the adjustment racks (diag. 7 A). If they are not positioned
as shown in diagram 7 B), release the front joints of the backrest
(point 8 of the instructions) and reassemble them (following the
instructions indicated in point 6), making sure to position correctly
the levers under the racks.
Fit the fabric cover on the seat, following, in the reverse order,
the strollers' instructions indicated in the paragraph "HOW TO
REMOVE THE FABRIC COVER".
WARNING: Before using the product in the stroller version, always
check that the backrest is fitted into the correct position.
HoW To REMoV E THE BACKREST
Remove the seat's fabric cover, following the instructions of the
stroller, indicated in the paragraph "HOW TO REMOVE THE
FABRIC COVER".
8. First release the front joint, by pressing the release button
located on the side (E) and pulling the tube of the backrest in
an upward direction (diag. 8). Repeat the operation on the other
side of the backrest.
9. Now release the rear joint, pressing the locking pin (G) and,
at the same time, pulling the joint inside (diag. 9). Repeat the
operation on the other side of the backrest.
HoW To REMoVE THE FABRIC CoVER
The fabric cover of the stroller can be removed.
To remove the fabric cover, hold the stroller in a semi-closed
position with the safety harness open.
10. Raise the leg rest and remove the fabric cover, taking care to
slide the safety harness through the cover (diag. 10).
11. Unfasten the press studs in the points shown in diagram
11A-11B.
12. Unfasten the press studs located on the armrests (diag. 12).
13. Lastly, remove the cover from the backrest, pulling it in an
upward direction (diag. 13).
HoW To FIT THE FABRIC CoVER
To fit the fabric cover to the stroller, carry out the following
operations.
14. Fit the fabric cover on the backrest of the stroller (diag. 14).
15. Fix the fabric cover to the seat, fastening the press studs as
shown in diagram 15A-15B.
16. Fix the fabric panels of the armrests by fastening the 2 press
studs, as shown in diagram 16.
17. Fit the fabric cover to the leg rest (diag. 17).
HoW To USE THE SAFETy HARnESS
This stroller has a 5-point safety harness that features two shoulder
straps, a waist strap and a crotch strap with buckle.
WARNING: When using the safety harness with children from
birth up to approximately 6 months of age, it is necessary to first
fit the shoulder straps through the two adjustment holes on the
fabric backrest.
18. Insert the shoulder straps through the appropriate holes in the
fabric backrest (diag. 18 A) and check that the shoulder straps are
adjusted at the correct height for your child. If they are not at the
correct height, adjust them as required (diag. 18 B).
19. After sitting the child in the stroller, insert the 2 prongs into
the buckle and, if necessary, adjust the width of the waist belt
operating the buckles (diag. 19).
20. To ensure maximum safety, the stroller has "D" rings to allow
you to fasten an additional safety harness approved to BS 6684
regulation. The rings are located inside the stroller's seat, on the
right and left side, as shown in diagram 20.
21. To unfasten the waist strap, press and pull the side prongs at
the same time (diag. 21).
WARNING: To ensure your child's safety, it is necessary to always
use the safety harness.
WARNING: the use of the crotch strap and safety harness is
necessary to guarantee the safety of your child.
HoW To ADjUST THE BACKREST
22. To adjust the inclination of the backrest, press the button
located on the backrest. Release the button to lock the backrest
in the nearest position. To raise the backrest, simply push it in an
upward direction (diag. 22).
WARNING: The child's weight can make these operations more
difficult.
HoW To ADjUST THE LEG REST
23. Press the two tabs to adjust the leg rest to the desired position
(diag. 23).
REMoVABLE BUMPER BAR
24. To remove the bumper bar, press the two buttons located under the
armrests (diag. 24) and pull the bumper bar towards you.
Open only one side of the bumper bar to place the child into the
stroller more easily.
WARNING: Always fasten the child with the safety harness. The
bumper bar is NOT a child restraint device.
WARNING: Never use the bumper bar to lift the stroller with the
child sitting in it.
ADjUSTABLE DoUBLE TWIST ERGonoMIC HAnDLE
25. Press the button, located on the handle, to turn the handle
to the desired position and adjust its height to the position that
is most comfortable for the user.
The handle can be adjusted to 8 different positions (diag. 25).
REAR BRAKES
The rear wheels have linked brakes, which can be applied
simultaneously to the two double rear wheels by using only
19