Step 3: Assign The Dmx Start Addresses Manually; Step 4: Assign The Dmx Channels To The Control Elements - EuroLite DMX Move BIGFOOT Bedienungsanleitung

Fixture Start address
1 1
2 17
3 33
4 49
5 65
6 81
Table 6.1 Default values for the starting address of the fixtures

Step 3: Assign the DMX start addresses manually

It is possible to split to the 192 available DMX addresses among the fixtures as desired.
1 Use the FIXTURE buttons to select the first fixture of which the DMX start address is to be assigned (adjacent
LED lights).
2 This menu item allows adjusting further characteristics. Use the SWAP button to switch between the options.
3 Select the "DMX START ADDR" option to assign the DMX start address. The lower display indicates the
default value e.g. "ADD: 065".
4 Change the address with the buttons of the lower display and press the ENTER button to memorize your
setting. To confirm the memory procedure, all LEDs of the controller flash three times.
● Usually the first device is assigned the address. 1 The second device receives the next free DMX channel as
start address. If the first device requires, for example, 14 DMX channels, the start address of the second device
must be assigned to the 15th channel. Proceed according to this scheme, until all spots receive a start
address assigned to the console.
● If the display inserts an "!" behind the set start address, an overlap in the DMX addresses exists. Several spots
then try to access the same DMX address. This is usually the case, if you have already assigned the start
addresses, yet have not entered the lighting functions and thus also not the number of channels. To assign the
functions on the console, see the next section. However, if you edit the lighting functions and channels and an
"!" is still displayed behind starting addresses, entries are incorrect.
5 Use the SWAP button to adjust further characteristics for the control channels or press the ESC button to exit
the "Patch fixture" menu and abort the configuration.

Step 4: Assign the DMX channels to the control elements

It is possible to individually assign the DMX channels of the connected spotlights to the control elements of the
controller (softpatch). However, some DMX channels must be assigned according to a certain scheme, in order
for the controller to correctly perform the integrated movements, color effects and fade effects. For control of the
RGB light effect units, the DMX channels which control red, green and blue and the dimmer function, must be
assigned to the encoders 1-4, and for control of the pan/tilt function of moving heads or scanners, the
corresponding DMX channels must be assigned to the encoders 15 and 16.
1 Select the option "Fixture Channel Patch" with the SWAP button to start the assignment. The lower display
indicates the control element on left side, e.g. "Fader CH:1/D " and the DMX channel on the right side, e.g.
"DMX CH:01". Please refer to the fixture's DMX protocol, which usually is part of the user manual.
2 Use the two left buttons of the lower display to adjust the control element and assign the DMX channel with the
two right buttons. As the first channel is reserved for the dimmer, please assign the fixture's dimmer channel
with the two right buttons. Confirm with the ENTER button. All LEDs of the controller flash three times to
confirm.
3 Then configure the color channels. Use the two left buttons to go one step further. "2/R" appears. With the two
right buttons assign the DMX channel for red. Assign channel 3 to green and channel 4 to blue. As of channel
5, the assignment is just a suggestion. The channels for the pan/tilt movement can be found in at the very end
on the list. These must also be assigned to the appropriate channels. All other channels used, you can be
assigned freely. Always confirm with the ENTER button.
4 All unused channels must be zeroed. For this, scroll through the patch list and press the DEL button
(indication "N1"). All LEDs of the controller flash three times to confirm.
Fixture Start address
7 97
8 113
9 129
10 145
11 161
12 177
25 • EN