Product Description And Specifications - Bosch C-EXACT 1 Originalbetriebsanleitung

OBJ_BUCH-1401-003.book Page 14 Tuesday, February 24, 2015 11:26 AM
14 | English
 Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or en-
ergising power tools that have the switch on invites acci-
dents.
 Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
 Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
 Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
 If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
Power tool use and care
 Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
 Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
 Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
 Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
 Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
1 609 92A 136 | (24.2.15)
Safety instructions for corded straight screw-
drivers
 Hold power tool by insulated gripping surfaces when
performing an operation where the screw may contact
hidden wiring, the tool's own cord or the mains cable.
Fasteners contacting a live wire may make exposed metal
parts of the power tool live and could give the operator an
electric shock.
 Do not drill, fasten or break into existing walls or other
blind areas where electrical wiring may exist. If this sit-
uation is unavoidable, disconnect all fuses or circuit break-
ers feeding this worksite.
 Hold the machine with a firm grip. High reaction torque
can briefly occur while driving in and loosening screws.
 Use only flawless tool bits that are not worn. Defective
tool bits can break, for example, and cause injury or dam-
age.
 When working with an application tool, pay attention
that the application tool is firmly seated on the tool
holder. When the application tool is not firmly connected
with the tool holder, it can come loose again and not be
controlled.
 Do not use this tool as a drill. Tools equipped with shut-
off clutches are not designed for drilling applications. The
clutch can shut off automatically and without warning.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
The dust developing during sanding,
WARNING
sawing, grinding, drilling and similar
operations can act carcinogenic, teratogenic or mutagen-
ic. Some of the substances contained in these dusts are:
– Lead in lead-based paints and varnishes;
– Crystalline silica in bricks, cement and other masonry
work;
– Arsenic and chromate in chemically treated wood.
The risk of disease depends on how often you are exposed to
these substances. To reduce the risk, you should work only in
well ventilated rooms with appropriate protective equipment
(e. g. with specially designed respirators that filter out even
the smallest dust particles).
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Bosch Power Tools