Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch GOP 300 SCE Professional Originalbetriebsanleitung

All manuals and user guides at all-guides.com
OBJ_BUCH-1271-006.book Page 14 Friday, April 29, 2016 9:48 AM
14 | English
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Wear protective gloves when changing application
tools/accessories. Application tools/accessories become
hot after prolonged usage.
 Do not scrape wetted materials (e.g. wallpaper) or on
moist surfaces. Penetration of water into the machine in-
creases the risk of an electric shock.
 Do not treat the surface to be worked with solvent-con-
taining fluids. Materials being warmed up by the scraping
can cause toxic vapours to develop.
 Exercise extreme caution when handling the scraper.
The accessory is very sharp; danger of injury.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.

Technical Data

Multi-Cutter
Article number
Preselection of orbital stroke rate
Rated power input
Output power
No-load speed n
0
Oscillation angle, left/right
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
1 609 92A 2PJ | (29.4.16)

Intended Use

The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e. g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Thumbwheel for orbit frequency preselection
3 Venting slots
4 Tool holder
5 Handle (insulated gripping surface)
6 Plunge saw blade*
7 Clamping bolt with spring washer (GOP 250 CE)
8 Hex key
9 Adapter for tool holder (GOP 250 CE)
10 Sanding plate*
11 Sanding sheet*
12 SDS lever for releasing the application tool
(GOP 300 SCE)
13 Felt ring of the dust extraction*
14 Retaining clip of the dust extraction*
15 Vacuum connection*
16 Dust extraction*
17 Vacuum hose*
18 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GOP 250 CE
3 601 B30 0..

W 250
W 150
-1
min 8000–20000
° 1.4
kg 1.5
/II
GOP 300 SCE
3 601 B30 5..

300
180
8000–20000
1.4
1.6
/II
Bosch Power Tools