Product Description And Specifications; Intended Use; Product Features - Bosch GOF Professional 1250 LCE Originalbetriebsanleitung

16 | English
power tool "live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it un-
stable and may lead to loss of control.
The permitted speed of the cutting bit must be at least
u
equal to the maximum speed marked on the power
tool. If cutting bits run faster than their rated speed, they
may break and fly off.
Routers and other accessories must be able to fit ex-
u
actly in the tool holder (collet) of your power tool. Ap-
plication tools that do not fit exactly in the tool holder of
the power tool will turn unevenly, vibrate heavily and may
cause a loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Do not put your hands in the routing area or close to
u
the router. Grip the auxiliary handle with your other
hand. Holding the router with both hands avoids injury.
Never rout over metal objects, nails or screws. The
u
router could become damaged and cause increased vibra-
tion.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not use blunt or damaged routers. Blunt or damaged
u
routers cause increased friction, create imbalances and
may become jammed.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Never swallow button cells. Swallowing button cells can
u
result in severe internal burns and death within two
hours.
1 609 92A 57T | (03.02.2020)
Ensure that the button cell is kept out of the
reach of children. If you suspect that
someone has swallowed a button cell or that a
button cell has entered the body in another
way, seek medical attention immediately.
Ensure that battery replacement is carried out prop-
u
erly. There is a risk of explosion.
Do not attempt to recharge the button cell and do not
u
short circuit the button cell. The button cell may leak,
explode, catch fire and cause personal injury.
Remove and dispose of drained button cells correctly.
u
Drained button cells may leak and damage the product or
cause personal injury.
Do not overheat the button cell or throw it into fire.
u
The button cell may leak, explode, catch fire and cause
personal injury.
Do not damage the button cell and or take the button
u
cell apart. The button cell may leak, explode, catch fire
and cause personal injury.
Do not allow damaged button cells to come into con-
u
tact with water. Leaking lithium may mix with water to
create hydrogen, which could cause a fire, an explosion,
or personal injury.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for copy routing as well as routing
grooves, edges, profiles and elongated holes in wood,
plastic and light building materials while resting firmly on the
workpiece.
Can even be used to machine non-ferrous metals when used
at a low speed with the appropriate router bits.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Right handle (insulated gripping surface)
(2) Lock-on button for on/off switch
(3) Light ring (GOF 1250 LCE)
(4) Cap nut with collet
A)
(5) Router bit
(6) Spindle locking lever
Bosch Power Tools