Pro And Multizentrale; Connecting The Multimaus; Pro - roco multiMAUS PRO Handbuch

1.1 Connecting the multiMAUS

A functional ROCO digital system with multiMAUS
A transformer or switching power supply unit (e.g. ROCO 10850, Fleischmann 681301, see also page 80),
▪
A feeder track without capacitor (e.g. geoLINE 61190, ROCO LINE 42517, Fleischmann 9400, 22217 (N),
▪
6430 (H0)).
Fig. 2 on page 89 shows the basic connection of the individual devices.
The fourth and fifth part of this manual starting on page 80 describes the additional devices that can be connected
to the multiZENTRALE or used with the ROCO digital system.

PRO

Please pay attention to the following instructions before starting to connect components:
The warranty will be voided if you are using ROCO and/or Fleischmann components together with components
from other companies. In addition, there is a risk of damage or malfunction to your digital system. Your war-
ranty will also become void if you open the housing of the multiMAUS
multiZENTRALE .
PRO
Please only carry out any connection work with the operating voltage switched off (exception: connecting ad-
ditional RocoNet devices, see page 80). Please use care when connecting devices to the track system to prevent
short circuits! An incorrect connection may destroy the digital components. Please seek the advice of a specialist
or local dealer if needed.
It is imperative that you do not connect a normal transformer on the same circuit parallel to the digital control
system. Doing so may destroy the multiZENTRALE
Previous ROCO amplifiers model 10761 and 10764 cannot be used together with the multiMAUS
multiZENTRALE .
PRO
The multiMAUS is supplied with electricity by 3 AAA batteries (micro) each with 1.5 V or 3 rechargeable batteries
PRO
of the same type (1.2 V each). Batteries must be inserted with the polarity aligned and batteries or rechargeable
batteries must have the same charge! Please consult the rear page of the manual for additional information about
the use of batteries and rechargeable batteries.
1. Position the multiZENTRALE
multiMAUS is not obstructed.
PRO
2. Plug the feeder track cable into the "Main
3. Plug the hollow plug, which is connected to the transformer or switching power supply with the two–pin cable,
into the "Power In" socket.
4. You can now (and not beforehand) connect the transformer/switching power supply to the mains socket. This
way prevents damaging the digital system.
5. Open the battery compartment in the rear of the multiMAUS
standard or rechargeable batteries. Please make sure the polarity is correct! Use the screw to re-close the bat-
tery compartment.
6. Press the "Light /OK" key to switch the multiMAUS
select the language version by pressing the "arrow keys". Press "Light /OK" again. The scrolling text "PRESS
BUTTON ON CENTRE FOR 3 SEC" is displayed.
7. After pressing the white "Connect" key on the multiZENTRALE
LEDs light up first followed by all four LEDs in the manner of a running light. The display restarts and "LOCO
1" with flashing STOP symbol is depicted.
The yellow LED flashes on the multiZENTRALE
start operating the trains. An antenna symbol in the upper right of the display or the continuously lit green
LED below the wireless symbol on the multiZENTRALE
multiMAUS and multiZENTRALE
PRO
8. To switch the multiMAUS
Part 1
▪
and multiZENTRALE
PRO
and multiZENTRALE
PRO
!
PRO
centrally on the system in a way that the wireless connection to the
PRO
" track socket of the multiZENTRALE
PRO
. Simply press the "STOP" key of the multiMAUS
PRO
has been established correctly.
PRO
off, press the "Light /OK" key together with the "MENU" key.
PRO
Basics
PRO
requires the following items:
PRO
PRO (except battery compartment) and the
(remove screws), unlatch the catch, and insert
PRO
on. All of the display symbols are depicted briefly. Now
for at least 3 seconds, the red and yellow
PRO
indicate that the wireless connection between the
PRO
and
PRO
.
PRO
to
PRO
49