Operating Elements - Clatronic DVD 534 HC Bedienungsanleitung

DVD 534 HC - GB 25.06.2002 10:00 Uhr
of the device to the corresponding DIGITAL AUDIO IN di-
gital input then connect this to the »OPTICAL OUT« 54
(B) socket. The required connection cable can be obtai-
ned from your local shop.
Connecting a Digital Audio Recorder (DAT):
Via the digital outputs 54, you can copy CDs to DAT
cassettes or to a CD recorder without any loss of quality.
To do this, connect the »COAXIAL OUT« 54 (A) digital
audio socket to the DIGITAL IN input socket at the digital
recorder. If the digital recorder has an optical input then
connect this to the »OPTICAL OUT« 54 (B) socket. The
required connection cable is available form your local
store.
Connecting analog playback devices:
You can also listen to the sound from other playback ap-
pliances such as a stereo television, stereo video recor-
der, CD placer, DVD placer or satellite receiver over the
speakers of the surround systems by connecting these to
the »AUDIO IN« 53 sockets. To do this, connect the
sound output sockets (AUDIO OUT) or SCART) of the ap-
propriate device to the sound inputs AUDIO IN »AUX1«
or »AUX 2« 53 (C) These inputs are identical and can be
used as required. Their designations are only used in or-
der for easier differentiation when switching on the sound
source. The required connection cable and adapters are
available from your local store.
Warning:
– Make sure that you maintain the correct polarity (red =
right R, white = left L)..
– The audio output (AUDIO OUT) has to be switched to
ANALOG in the menu (see page XX-XX)
– To playback, the corresponding source »SOURCE«
13 or »AUX« 28 must be switched to the respective
sound source using »AUX 1« or »AUX 2«.
Open facing page 3. This allows you to find the parts mo-
re easily.
Front of the device
1 I PREV/NEXT
selection of title, section, music title / manual station
tuning / station search
2 í STOP
Cancels CD playback / deletes the CD program
memory
3 II PLAY/PAUSE
Stars CD playback / interrupts CD playback for a short
time, freeze-frame
4 REMOTE SENSOR
Remote control receiver
5 ADJ/VOL.+ / ADJ/VOL. -
to set the desired volume
Seite 33

Operating elements

I
Headphone connection:
The socket »PHONES« 11 is for all commercially availa-
ble headphones equipped with a 6.3mm jack. For other
jacks, use an adapter (available from specialised
dealers).
Notes:
– The connected speakers are switched off when using
the headphones.
– When plugging in the jack, the system automatically
switches over to STEREO.
– The following message appears for a short time when
plugging in the headphone jack:
Caution!
High volumes especially of headphones, can damage
your hearing.
Mains connection 56
Only connect the device to the mains after all other
connections have been made. To connect to the mains,
plug the mains plug into the socket. Also plug in the
mains plug of the subwoofer.
Caution!
If the mains plug of the device is faulty or if the device is
otherwise damaged then it must not be put into operati-
on.
When removing the mains cable from the socket then
always pull on the mains plug – not on the cable.
Warning:
To avoid damage from lightning pull the mains and aeri-
al plug during thunderstorms.
6 POWER
Mains switch for switching on or off the device
7 STANDBY / MUTE
Standby indicator / Mute indicator
8 CD-tray
9 OPEN / CLOSE
Opens and closes the CD tray
10 Display unit
11 PHONES
Headphone socket
12 SELECT
Selects the individual sound channels for setting the
volume
13 SOURCE
Selects the sound source DVD, TUNER FM, TUNER
AM, AUX 1, AUX 2
33