English Gb - Honeywell HYF500E Betriebsanleitung

HYF500E
COMPONENTS
3
4
6
5
2
1
ASSEMBLY INSTRUCTIONS
Fig. 1 Fig. 2
Fig. 5 Fig. 6
CONTROL PANEL
4
6
Fig. 7 Fig. 8
Fig. 3 Fig. 4
2
IMPORTANT SAFETY INSTRUCTIONS
Read through all the instructions
before starting to use the appliance. Keep
this manual in a safe place for future
reference.
These instructions are also available on
our website. Please visit
www.hot-europe.com.
6
WARNING:
• This appliance must only be operated
as instructed in this user manual.
5
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
• Children shall not play with the
appliance.
• Cleaning and user maintenance shall
not be made by children without
supervision.
• Clean the appliance regularly by
following the "Cleaning Instructions".
• This appliance is only designed for
indoor use.
• Unwind the power cord completely.
Failure to do so could cause
overheating and possible fire hazard.
• Do not tug at the power cord to
disconnect the plug. Do not touch the
power cord with wet hands. Do not
remove the power plug from the power
socket while the product is in use.
• Do not use accessories, spare parts
or components not expected and / or
provided by the manufacturer.
• Always switch the appliance off and
disconnect the power plug from the
power socket when the appliance is not
in use or during transport.

ENGLISH GB

• Do not use this appliance if it is
damaged or shows any signs of possible
damage or if it is not functioning
properly. Disconnect the power plug
from the power socket.
• If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
• Never touch the unit with wet hands.
COMPONENTS
1. Base
2. Bottom fan
3. Top fan
4. Top fan speed control
5. Bottom fan speed control
6. Oscillation button
FIRST TIME OF USE
1. Read through all the instructions before starting to use the fan.
2. Unpack all the parts of the fan. Remove all packaging materials and
dispose of them for recycling.
3. Place the fan on a firm, even surface. Make sure that it is standing
securely so that it cannot tip or fall over. A safety distance of at least
50 cm from other objects must be observed.
ASSEMBLY INSTRUCTIONS
(See page 2)
A. BASE ASSEMBLY
• Align the front and back base pieces and gently push the halves until
the pieces snap securely together. (Fig. 1).
B. SECURING THE TOWER FAN TO THE BASE
• At the base of the housing, remove the locking nut and set aside (Fig. 2)
• Carefully lift the fan housing (Fig. 3) and place the power cord through
the center of the base.
• Lower the fan housing into the base (Fig. 4).
• Take the locking nut and place the power cord through the locking nut
and move the nut up inside the base, (Fig. 5) attach the locking nut to
the fan housing by turning clockwise until fully tightened.
• The fan cord can exit either side of the base; choose which one is closer
to your outlet. (Fig. 6)
• The back of this fan is intentionally closed. This allows the air intake and
exit to happen at the front grille. This aerodynamic cross-flow design
harnesses the Turbo Force® power of your fan!
NOTE: DO NOT operate the tower fan unless it is in its proper, upright
position.
OPERATING INSTRUCTIONS
• Be sure the fans are in the off position.
• Place your fan on a dry, level surface.
• Plug the power cord into a polarized 220 volt AC wall outlet.
Individual controls allow you to operate each fan independently.
TOP FAN SPEED CONTROL
Turn the control knob to the desired fan speed High ( ), Medium (
or Low ( ) (Fig. 7).
3
)