Ryobi RBC-254FC Bedienungsanleitung Seite 28

GB
F D E
OPERATION
FILLING THE TANK
Clean surface around fuel cap to prevent
■
contamination.
Loosen fuel cap slowly to release pressure and to
■
keep fuel from escaping around the cap.
Carefully pour fuel mixture into the tank. Avoid spillage.
■
Prior to replacing the fuel cap, clean and inspect
■
the gasket.
Immediately replace fuel cap and hand tighten.
■
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
NOTE: It is normal for smoke to be emitted from a
new engine during and after first use.
WARNING
Always shut off engine before fueling. Never add
fuel to a machine with a running or hot engine.
Move at least 9 m from refueling site before
starting engine. Do not smoke!
1 Litre +
2 Litres +
3 Litres +
4 Litres +
5 Litres +
OPERATING THE TRIMMER (Fig. 8)
Hold the trimmer with the right hand on the trigger handle
and the left hand on the left handle. Keep a firm grip with
both hands while in operation. Trimmer should be held at a
comfortable position with the trigger handle about hip height.
Always operate trimmer at full throttle. Cut tall grass from
the top down. This will prevent grass from wrapping
around the shaft housing and string head which may
cause damage from overheating. If grass becomes
wrapped around the string head, stop the engine,
disconnect the spark plug wire, and remove the grass.
Prolonged cutting at partial throttle will result in oil
dripping from the silencer.
I P NL S DK
20 ml =
40 ml =
60 ml = 50:1 (2%)
80 ml =
100 ml =
N FIN GR HU CZ RU
English
ADVANCING THE STRING
ADVANCING STRING USING THE EZ LINE™ TAP
ADVANCE SYSTEM
String advance is controlled by tapping string head on
grass while running engine at full throttle.
Run engine at full throttle.
■
Tap string head on ground to advance string.
■
String advances each time the head is tapped.
Several taps may be required until string strikes the
■
cutoff blade.
Resume trimming.
■
NOTE: If the string is worn too short you may not be able
to advance the string by tapping it on the ground. If so,
STOP THE ENGINE, and manually advance the string.
ADVANCING THE STRING MANUALLY
Push the spool retainer down while pulling on string(s) to
manually advance the string.
CUTTING TIPS (Fig. 9)
Keep the trimmer tilted towards the area being cut;
■
this is the best cutting area (45).
Do not cut in dangerous cutting area (43).
■
Use the tip of string to do the cutting; do not force
■
string head into uncut grass.
Wire and picket fences cause extra string wear,
■
even breakage. Stone and brick walls, kerbs and
wood may wear string rapidly.
Avoid trees and shrubs. Tree bark, wood mouldings,
■
cladding and fence posts can easily be damaged by
the string.
GRASS DEFLECTOR LINE TRIMMING CUTOFF
BLADE (Fig. 10)
This trimmer is equipped with a line trimming cut-off
blade on the grass deflector. For best cutting, advance
string until it is trimmed to length by the cut-off blade.
Advance string whenever you hear the engine running
faster than normal. This will maintain best performance
and keep string long enough to advance properly.
OPERATING THE BRUSHCUTTER (Fig. 11-12)
Hold the brushcutter with the right hand on the trigger
handle and the left hand on the left handle. Keep a firm grip
with both hands while in operation. Brushcutter should be
held at a comfortable position with the trigger handle about
hip height. Maintain your grip and balance on both feet.
Position yourself so that you will not be drawn off balance
by the kick-back reaction of the cutting blade.
20
RO PL SLO HR TR EST LT LV SK BG