Herunterladen Inhalt Inhalt Diese Seite drucken

Working Instructions - Scheppach BCH3200PB4 Originalbetriebsanleitung

Benzin motorsense
Vorschau ausblenden Andere Handbücher für BCH3200PB4:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Draining fuel. Fig. 40
• Hold a collection container beneath the fuel drain bolt.
• Unscrew the tank cap and remove it.
• Allow the fuel to run out completely.
• Screw the tank cap on firmly by hand.
Start on the unit
Do not start the unit until it has been completely assem-
bled.
m Danger of injury!
Do not operate the device unless you did not find
any faults. If a part has become defective, make sure
to replace it before you use the device again.
Check before use!
• Check the safe condition of the device:
• Check the device for leaks.
• Check the device for visual defects.
• Check that all parts of the device have been securely
fitted.
• Check that all safety devices are in proper condition.
m Danger of injury!
Before starting work, always check the ground and re-
move all objects which could be thrown by the device.
Start Fig. 21 - 27 + 41
Once the machine has been set up properly, start the en-
gine as follow:
1. Set the equipment down on a hard, level surface.
2. Turn the engine switch to the ON position. Fig. 23
3. Put the choke lever on the
4. Press the fuel pump more than 5 times. Fig. 24
5. Pull the recoil starter handle 3-5 times to start the en-
gine. Fig. 25
6. Wait a while adjust the choke lever to
Fig. 26
7. Pull the rope until engine starts. Fig. 25
8. When the engine is running and idling. The throttle le-
ver on handle is as picture 25. First press the lock off
lever (7) and then switch the throttle lever (8) on, the
machine will be working. If you want to lock the throttle
lever (8) press the throttle lever lock (9). Fig. 27
9. Adjusting line length when working:
This machine is fitted with a "Tap & Go"head.To re-
lease more line, tap the cutting line head against the
round with engine at top speed: the line will be re-
leased automatically and the knife cut off the excess
length. Fig. 41
10. If meet any problems, press the engine switch to off
position, the machine will stop running. If need stop
cutting head working, release the throttle lever (8).
Fig. 27
11. If any problem occurs, pull the pin of safety belt, then
release the brush cutter immediately. Fig. 22
12. If the machine is hot, the throttle level can be adjust-
ed to ON position directly when re start the machine.
Note: If the engine does not start up even after several
attempts, read the section „Engine troubleshooting".
position. Fig. 23
position.
Note: Always pull the starter cord out in a straight line. If
it is pulled out at an angle, then friction will occur on the
eyelet. As a result of this friction, the cable will become
frayed and will wear away faster. Always hold the starter
handle when the cable retracts.
Never allow the cable to snap back when it has been
pulled out.
Note: Do not start the motor in tall grass.
m Attention: When the engine has been switched off,
the cutter continues running for several seconds there-
fore do not close to cutting head of brush cutter until the
cutter has come to a standstill!

9. Working instructions

Extending the cutting line
Caution! Do not use any kind of metal wire or metal wire
encased in plastic in the line spool. This may cause seri-
ous injuries to the user. To extend the cutting line, run the
engine at full speed and tap the line spool on the ground.
This will automatically extend the line. Fig. 41
The blade on the safety shield will cut the line to the ap-
propriate length. Fig. 16
m Important: Remove all grass and weed remnants at
regular intervals to prevent the shaft tube overheating.
Lawn, grass and weed remnants become trapped under
the safety shield and prevent the shaft tube from receiv-
ing adequate ventilation. Remove the remnants carefully
using a screwdriver or the like. Fig. 42
Different cutting methods
When the equipment is correctly assembled it will cut
weeds and long grass in places which are diffi cult to ac-
cess, e.g. along fences, walls and foundations and also
around trees. It can also be used for „mowing" down
vegetation so that a garden can be better prepared or a
certain area cleared down to the soil. Fig. 43
m Attention: Even if it is used carefully, cutting around
foundations, stone or concrete walls, etc. will result in the
line suff ering more than normal wear.
Trimming/mowing
Swing the trimmer from side to side in a scything motion.
Always keep the line spool parallel to the ground. Check
the site and decide which cutting height you require.
Guide and hold the line spool at the required height to
obtain an even cut. Fig. 43
Low trimming
Hold the trimmer right in front of you at a slight angle so
that the underside of the line spool is above the ground
and the line strikes the correct target. Always cut away
from yourself. Never draw the trimmer towards yourself.
GB
25

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis