Specifications - Makita GA7012C Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Lock lever
2-2. Switch trigger
3-1. Indication lamp
4-1. Side grip
5-1. Wheel guard
5-2. Screw
5-3. Bearing box
6-1. Wheel guard
6-2. Nut
6-3. Lever
6-4. Bearing box
7-1. Nut
7-2. Lever
8-1. Lock nut
8-2. Depressed center grinding
wheel/Multi-disc
8-3. Inner flange

SPECIFICATIONS

Depressed center wheel diameter
No load speed (n
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For Model GA7012C
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Explanation of general view
8-4. Super flange
9-1. Lock nut
9-2. Depressed center wheel/Multi disc
9-3. Inner flange
10-1. Lock nut wrench
10-2. Shaft lock
11-1. Lock nut
11-2. Abrasive disc
11-3. Rubber pad
13-1. Wire cup brush
14-1. Wire wheel brush
15-1. Lock nut
15-2. Abrasive cut-off wheel/diamond
15-3. Inner flange
15-4. Wheel guard for abrasive cut-off
16-1. Lock nut
Model
Spindle thread
) / Rated speed (n)
o
Overall length
Net weight
Safety class
) : 90 dB(A)
pA
) : 101 dB(A)
WA
wheel
wheel/diamond wheel
ENE048-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
ENF002-1
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
If the tool is used for other applications, the vibration
values may be different.
Work mode: disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
ENG102-3
For Model GA9012C
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
4
16-2. Outer flange 78
16-3. Abrasive cut-off wheel/diamond
wheel
16-4. Inner flange 78
16-5. Wheel guard for abrasive cut-off
wheel/diamond wheel
17-1. Exhaust vent
17-2. Inhalation vent
18-1. Commutator
18-2. Insulating tip
18-3. Carbon brush
19-1. Brush holder cap
19-2. Screwdriver
GA7012C
180 mm
M14
-1
8400(min )
453 mm
4.3 kg
/II
) : 7.0 m/s
h,AG
2
) : 3.5m/s
h,SG
2
pA
) : 101 dB(A)
WA
GA9012C
230 mm
M14
-1
6000(min )
453 mm
4.5 kg
ENG208-4
2
ENG313-1
2
ENG102-3
) : 90 dB(A)