Set Up Battery Operation; Removing The Battery Box; Installing The Battery Pack; Installing The Battery Box - Dräger Polytron 6100 EC WL Gebrauchsanweisung

|
en Electrical installation
c. Put the protective cap (Fig. A 3) on the battery
contacts in the housing.
5. Close the gas detector:
a. Place the housing cover in the final position (Dräger
logo horizontal).
b. Turn the housing cover under slight pressure approx.
20° counterclockwise until the housing cover rests on
the sealing ring on the housing.
c. Press the housing cover forcefully and evenly onto the
sealing ring.
d. Slowly turn the housing cover approx. 20° clockwise to
the stop in the end position.
e. Screw in the locking screw (Fig. A 14) until the housing
cover is prevented from being screwed open.
6. Configure the gas detector with PolySoft for operation with
wired power supply.
6.2

Set up battery operation

The transport, insertion and replacement of the battery box in
potentially explosive gas atmospheres is permitted.
In a dust explosion hazardous area, the short-term transport
of the battery box is permissible. Inserting or changing the
battery box in a potentially explosive dust atmosphere is only
permitted with declassification.
Replacing the battery pack is also explained in PolySoft .

6.2.1 Removing the battery box

WARNING
Risk of explosion!
If the gas detector is opened in a potentially explosive dust
atmosphere, an explosion may occur.
► Do not open the gas detector in dust explosion-hazard
areas. Alternatively, declassify the dust explosion-hazard
area beforehand.
Remove the battery box:
1. Open the gas detector:
a. Loosen the set screw (Fig. A 14).
b. Turn the housing cover (Fig. A 1) approx. 20°
counterclockwise and remove it.
2. Pull out the battery box (Fig. A 2).

6.2.2 Installing the battery pack

WARNING
Risk of explosion!
Opening the battery box in a hazardous area can cause an
explosion.
► Do not open the battery box in an explosion-hazard area.
Alternatively, declassify the explosion-hazard area
beforehand.
28
NOTICE
Incorrect calculation of the remaining charge!
► When inserting or changing the battery pack, only use new
Prerequisite:
– Battery box has been removed.
– Battery box is located outside the explosion-proof area
Install battery pack:
1. Loosen the screw (Fig. C 1).
2. Remove the lid (Fig. C 2) of the battery box.
3. When changing the battery pack, disconnect the cable
► Use only the Dräger LBT 05** (see "Accessories and
4. Open the seal on the new battery pack and connect the
5. Insert the battery pack in the battery box.
6. Reattach the battery box lid.
7. Tighten screw (Fig. C 1).
Subsequent activities:
– Install the battery box.

6.2.3 Installing the battery box

Prerequisites:
– The gas detector is open.
– Insert the battery pack into the battery box.
Install the battery box:
1. Connect grounding cable to fastening screw for potential
► Use only the Dräger LBT 03**(see "Accessories and spare
2. Insert battery box (Fig. A 2).
3. Close the gas detector:
Instructions for use |
Dräger Polytron
battery packs.
Exception: If the currently used battery pack is removed,
e.g., during maintenance, it may be used again.
connector (Fig. C 5) and remove the empty battery pack
from the battery box.
WARNING
spare parts", page 37) battery pack.
cable plug of the battery pack (Fig. C 5).
The cable plug of the battery pack must engage when
plugged in.
When closing the battery box, pay attention to the cable
to avoid damage.
equalization (Fig. A 17).
WARNING
parts", page 37) battery box.
a. Place the housing cover (Fig. A 1) in its final position
(Dräger logo is horizontal).
b. Turn the housing cover under slight pressure approx.
20° counterclockwise until the housing cover rests on
the sealing ring on the housing.
c. Press the housing cover forcefully and evenly onto the
sealing ring.
®
6100 EC WL, Dräger Polytron
®
Repeater ISA