General Information; Presentation Of The Installation; Welding Set Components; Technical Specifications - CEMONT PRECISA 200MP Bedienungs- Und Wartungsanleitung

EN

1 - GENERAL INFORMATION

1.1 - PRESENTATION OF THE INSTALLATION

PRECISA 200MP is a manual welding set multifunction that enables:
MIG-MAG welding with short arc using currents from 30 A to 200 A.
■
Feeding different types of wire (wire spool diameter Ø 200 mm
■
maximum, in option wire spool Ø 300 mm).
‫ ܟ‬Steel, stainless steel, aluminum and special wires
‫ ܟ‬solid and cored wires
‫ ܟ‬diameters from 0.6 mm to 1.0 mm (1.2 mm for aluminum in
manual mode)
Coated electrode welding using currents from 5 A to 200 A.
■
TIG welding using currents from 5 A to 200 A.
■

1.2 - WELDING SET COMPONENTS

Power source
■
Primary cable length 3 m
■
Earth cable with clamps length 3 m
■
Gas hose length 2 m
■
Safety manual
■

1.3 - TECHNICAL SPECIFICATIONS

PRIMARY
1-phase primary power supply
Frequency
Power
SECONDARY
No-load voltage
Current range 30 A – 200 A
Duty cycle 100 % at 40° C
Duty cycle 60 % at 40° C
Duty cycle 20 % at 40°C
Protection degree
Isolation class
Standard
Dimensions (L x l x h)
Net weight
WARNING: WITH A 16 A FUSE, THE MAXIMUM WELDING CURRENT
IS 150 A. FOR POWER OVER 150 A , A 25 A FUSE AND A SUITABLE
POWER PLUG ARE REQUIRED.
WARNING: THE HANDLE IS NOT INTENDED FOR SLINGING THE
SET, BUT ONLY TO CARRY THE MACHINE AND FOR NEGOTIATING
OBSTACLES (CABLES IN A WORKSHOP, A 10 CM STEP, ETC). THIS
EQUIPMENT HAS A PROTECTION DEGREE IP22S.IT CANNOT BE
USED UNDER RAIN OR SNOW. IT CAN BE STORED OUTSIDE BUT IT
IS NOT DESIGNED TO BE USED DURING PRECIPITATION WITHOUT
PROTECTION.
PRECISA 200MP
W000377722
230 V +/-10 %
50 / 60 Hz
8,6 kVA
MIG MMA TIG
35 V 65 V 65 V
5 A – 200 A 5 A – 200 A
105 A 95 A 120 A
130 A 120 A 130 A
200 A 200 A 200 A (30%)
IP 22S
H
EN60974-1 / EN60974-5 / EN60974-10
500 x 280 x 420 mm
15 kg
GENERAL INFORMATION
Code letter IP
First digit 2
1
Second digit 2
3
S
1.3.1 - TECHNICAL CHARACTERISTICS OF THE PART OF
WIRE FEED
Wire feeding
Wire feed speed
Wire diameter usable
Torch connection

1.4 - INSTALLATION

1.4.1 - CONNECTIONS

ELECTRICAL CONNECTIONS TO THE MAINS:
‫ ܟ‬PRECISA 200MP is a 230 V single phase welding set.
‫ ܟ‬PRECISA 200MP is compatible with power generator (12 kVA).
CAUTION: THE ELECTRICAL CONNECTION OF THE POWER
SOURCE MUST BE DONE BY QUALIFIED TECHNICIANS AND
THE POWER SUPPLY INSTALLATION MUST BE CORRECTLY
DIMENSIONED REGARDING THE CHARACTERISTICS OF THE
POWER SOURCE (ESPECIALLY CONCERNING THE MAXIMUM
CONSUMED CURRENT).
THIS EQUIPMENT DOES NOT COMPLY WITH IEC 61000-3-12.
IF IT IS CONNECTED TO A PUBLIC LOW VOLTAGE SYSTEM,
IT IS THE RESPONSIBILITY OF THE INSTALLER OR USER OF
THE EQUIPMENT TO ENSURE, BY CONSULTATION WITH THE
DISTRIBUTION NETWORK OPERATOR IF NECESSARY, THAT THE
EQUIPMENT MAY BE CONNECTED.
THIS CLASS A EQUIPMENT IS NOT INTENDED FOR USE IN
RESIDENTIAL LOCATIONS WHERE THE ELECTRICAL POWER
IS PROVIDED BY THE PUBLIC LOW-VOLTAGE SUPPLY SYSTEM.
THERE MAY BE POTENTIAL DIFFICULTIES IN ENSURING
ELECTROMAGNETIC COMPATIBILITY IN THOSE LOCATIONS, DUE
TO CONDUCTED AS WELL AS RADIATED DISTURBANCES.
CONNECTION OF THE TORCH:
The MIG welding torch is connected to the front of power source, after
ensuring it has been properly outfitted with the wear parts corresponding
to the wire used for welding.
For this purpose, please refer to the torch instructions.
4 - EN
Degrees of protection
Against penetration of solid foreign bodies with Ø ≥ 12,5
mm
Against penetration of vertical drops of water with harmful
effects
Against penetration of rain (inclined up to 15° in relation to
the vertical) with harmful effects
Against penetration of rain (inclined up to 60° in relation to
the vertical) with harmful effects
Indicates that testing for protection against the
undesirable effects of water penetration was carried out
with all parts of the equipment at idle.
2 rollers
1.6 → 20 m/min
0.6 → 1,0 mm (1.2 mm in aluminium)
European type