RADEMACHER RolloTube S-line DuoFern Original - Betriebs- Und Montageanleitung Seite 38

i
Contents
1. This manual... ............................................39
2. Hazard symbols .........................................39
2.1 Levels of danger and signal words ......39
2.2 Symbols and depictions used ...............39
3. Safety instructions ....................................40
3.1 Intended use / operational
conditions .....................................................41
3.2 Improper use ...............................................41
3.3 Required expert knowledge of the
installer ..........................................................41
3.4 Glossary - Definition .................................42
4. Scope of delivery for RolloTube S-line
DuoFern Small/Medium ............................43
5. General view of the RolloTube S-line
DuoFern for Small/Medium ......................44
6. Functional description ..............................45
6.1 Blockage detection function .................45
6.2 Obstacle detection function ..................46
6.3 Function of the shutter length
compensation .............................................46
6.4 Functions if the catch has been
mounted without the freewheel
mechanism ...................................................46
6.5 Jog mode using a roller shutter
button ............................................................46
6.6 Operation using a roller shutter
switch .............................................................47
6.7 Jog mode using a 1-pole button ..........47
6.8 Activating the fly screen door
protection .....................................................47
6.9 Activating log-on mode using the
DuoFern radio code ..................................47
7. Important installation instructions .........48
7.1 Installation of the tubular motor..........48
7.2 Mounting the bearings ............................49
7.3 Determining the length of the
winding shaft (5) ........................................49
7.4 Mounting / dismantling the
adapter (10)..................................................50
7.5 Dismantling the catch (8)........................50
7.6 Mounting the catch (8) with the
freewheel mechanism..............................51
7.7 Mounting the catch (8) without the
freewheel mechanism..............................51
7.8 Sliding the tubular motor (9) into
the winding shaft .......................................52
7.9 Preparation for use of the
precision tubes ..........................................52
7.10 Mounting the roller capsule (4) ............54
7.11 Mounting the motor into the
bearings ........................................................54
7.11.1 Mounting into the drive
7.11.2 Mounting in other drive
7.11.3 Mounting into the counter
38
bearing as a click
bearing (13) ...................................54
bearing versions ..........................54
bearing (1) .....................................55
7.12 Mounting the roller shutter (17) ...........55
7.12.1 Mounting the roller shutter
with rigid shaft connectors ......55
7.12.2 Mounting the roller shutter
with ties ..........................................56
7.12.3 Mounting roller shutter
stoppers or an end rail ..............56
8. Safety instructions for the electrical
connection .................................................57
8.1 Safe cable routing by fixing the
plug connection .........................................58
8.2 Connecting the motor cable (15) .........58
8.3 Electrical connection of the
tubular motor ..............................................59
8.3.1 Controlling the tubular motor
via radio ............................................59
8.3.2 Controlling the tubular motor
using a roller shutter switch or
button ................................................59
8.3.3 Controlling the tubular motor
using a 1-pole button (closer) ...60
8.3.4 Parallel connection of
several motors ................................60
8.4 Connection of the universal setting
cable for manual end point setting .....61
9. Self-learning mode with smooth stop .....62
10. Manual adjustment of end points ...........62
10.1 Test run / modifying the end points ...64
11. Reloading the factory settings .................65
12. What to do if... ? .........................................66
13. Technical specifications ............................67
14. Configuration of KNX/EIB Venetian blind
actuators for RADEMACHER tubular
motors ........................................................67
15. Simplified EU declaration of
conformity .................................................68
16. Logging DuoFern devices on/off..............69
16.1 Logging a DuoFern device on/off
using the set button .................................69
16.2 Logging a DuoFern device on/off
using a roller shutter switch/button
or universal setting cable ........................70
16.3 Activating log-on mode using the
DuoFern radio code ..................................71
17. Warranty terms and conditions .................72
EN