Steinbach Poolrunner Battery+ Bedienungsanleitung Seite 3

etting: 0 °—— 30 ° , for most of pools.
h
0 ㎡
³/h
Abbildung 3 / Illustration 3
0℃-35℃
a. Settings of nozzle angle and moving route
The nozzles of the cleaner are marked with angles (0°—40°).
min
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
4.! Clean the filter tray
The cleaner moves in a more curved line at a larger angle from 0°- 40°.
y)
b. Recommended three CYCLEs and nozzle settings
a.! Open the cleaner by clips
mperature: 0℃-45℃
Setting One: default setting: 0 °—— 30 ° , for most of pools.
Nozzle
angle
270（H）mm
month): -20℃-60℃，≤75%RH
3 months): -20℃-45℃，≤75%RH
months): -20℃-20℃，≤75%RH
Moving
route
Abbildung 5 /
pool with the cleaner bottom toward the wall to avoid any
Illustration 5
ol.
Clean the filter tray
! Open the cleaner by clips
b.! Take off the filter tray
Abbildung 8 /
Illustration 8
2
! Take off the filter tray
c.! Clean the filter tray and chassis
! Clean the filter tray and chassis
Abbildung 11 /
Illustration 11
e filter tray
the cleaner by clips
9
off the filter tray
4.! Clean the filter tray
a.! Open the cleaner by clips
a. Settings of nozzle angle and moving route
The nozzles of the cleaner are marked with angles (0°—40°).
The cleaner moves in an approximately straight line when the nozzle angle is 0°.
The cleaner moves in a more curved line at a larger angle from 0°- 40°.
b. Recommended three CYCLEs and nozzle settings
Setting One: default setting: 0 °—— 30 ° , for most of pools.
Nozzle
angle
b. Install the brush before use to avoid possible dirt leaks.
Moving
route
b.! Take off the filter tray
Abbildung 6 /
Illustration 6
c. Please ensure that top cover of the cleaner is tightly assembled with its chassis.
.
5
c.! Clean the filter tray and chassis
Abbildung 9 /
d. Power off the cleaner after use.
e. Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting
Illustration 9
into or lift out from pool.
f. It is necessary to stay on the water surface for 10-15 seconds until water flows out from
the cleaner to the pool before being placed on the ground.
g. Lift the handle or clips of the cleaner out from the pool.
3
b. Install the brush before use to avoid possible dirt leaks.
9
Abbildung 12 /
Illustration 12
c. Please ensure that top cover of the cleaner is tightly assembled with its chassis.
.
d. Power off the cleaner after use.
e. Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting
4.! Clean the filter tray
a.! Open the cleaner by clips
5
b.! Take off the filter tray
c.! Clean the filter tray and chassis
9
23. Storage condition:
Short term (less than 1 month): -20℃-60℃，≤75%RH
Medium term (less than 3 months): -20℃-45℃，≤75%RH
Long term (more than 3 months): -20℃-20℃，≤75%RH
IV. Operation instruction
.
Abbildung 4 /
1. Precautions
Illustration 4
a. Put into or lift out from pool with the cleaner bottom toward
possible scratch to the pool.
.
Abbildung 7 /
Illustration 7
Abbildung 10 /
Illustration 10
9
061013_v1909 ALL
2
.
3